| “This site contains affiliate links for which OEMDTC may be compensated” |
NHTSA Campaign Number: 18E055
Manufacturer Industrias Martinrea de Mexico SA de CV
Components SERVICE BRAKES, HYDRAULIC
Potential Number of Units Affected 3,931
Brake Hose Corrosion May Cause Brake Fluid Leak
A brake fluid
leak can reduce brake effectiveness, increasing the risk of a crash.
Summary
Industrias Martinrea de Mexico SA de CV (Martinrea) has submitted a Defect Information Report based upon decisions made by Chrysler (FCA US LLC) and Ford Motor Company to conduct recalls (numbers 18V277 and 18V389 respectively). The brake circuit hose assemblies located between the master cylinder and the hydraulic control unit, may have been manufactured without anti-corrosion plating on the coupling fittings, or “ferrules,” of the hoses. This can lead to premature corrosion, and result in a brake fluid leak.
Remedy
Martinrea is working with the affected vehicle manufacturers. Dealers for those manufacturers will replace the brake hoses, free of charge. Chrysler owners may contact Chrysler customer service at 1-800-853-1403. Chrysler’s number for this recall is U41. Ford owners may contact Ford customer service at 1-866-436-7332. Ford’s number for this recall is 18S19.
Notes
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.
Recall Acknowledgement
August 14, 2018
Loading...
Reload document 
Open in new tab
- Provides an extra margin of safety in extreme braking conditions
- Mix of polyglycol ethers ensures hot brake-system operation will not create dangerous vapor
- Excellent for ABS, disc and drum brake systems
- Delivers braking power when needed by avoiding a spongy pedal
- Both wet and dry boiling points exceed the minimum government standards
- High compatibility. Use with or direct replacement for DOT 3, DOT 4, and DOT 5. 1
- Extended Service Interval (ESI): Lasts 100 percent longer than DOT 3, 50 percent longer than DOT 4, and 10 percent longer than DOT 5. 1
- Exceeds all DOT 3, DOT 4, and DOT 5. 1 standards
- Wet boiling point ~ 365 DegreeF/Viscosity at -40 DegreeC ~ 685mm2/s
- Standard brake fluid has a recommended change interval of 2 years. The recommended change interval for Bosch ESI6 is 3 years.
- The 336⁰F wet boil point and 521⁰F dry boil point exceeds common characteristics for DOT 4 brake fluids
- Provides corrosion protection in brake components
- Matches needs of all DOT 4 manufacturer recommendations
- Compatible with all DOT 3 and DOT 4 applications
- Helps provide protection against brake failure from vapor lock
- Helps prevent corrosion in brake system
- Works with all brake system requiring DOT 3 fluids
- Exceeds federal motor vehicle safety standard No. 116
- Meets SAE spec. J1703.
- Premium DOT 3 Brake Fluid has a minimum boiling point of 450°F
- Meets and exceeds DOT 3 and all other Federal and SAE specifications and standards for motor vehicle brake fluids
- Mixes with all DOT 3 approved brake fluids
- Designed for use in disc, drum and ABS brake systems
- Premium brake and hydraulic clutch fluid that protects internal components from corrosion under normal use
- High boiling point to minimize brake fluid boiling and vapor lock
- Excellent low temperature capability and stability when used where lower cold viscosities are required
- Excellent low temperature capability and stability when used where lower cold viscosities are required
- Synthetic quality brake fluid
- Contains special ingredients to guard against vapor lock and moisture absorption
- Exceeds requirements for both DOT 3 and DOT 4 brake fluids
- Specially formulated for DOT 4 brake fluid applications
- Designed for use in disc, drum and ABS brake systems
- Maintains proper movement for safe, effective stopping performance
- Helps deliver a quieter braking system
- Produces smoother pedal travel
- Provides longer brake life and performance
- Install Wagner with total confidence
- An exclusive European formula with an exceptionally high boiling point and superior anti-vapor lock characteristics
- Superior braking during arduous conditions like racing and rallying
- Typical wet boiling point is 270deg. C
Last update on 2025-04-16 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.