April 7, 2021 NHTSA CAMPAIGN NUMBER: 21V244000
Inverter Error May Shutdown Electric Drive
A sudden loss of power increases the risk of a crash.
NHTSA Campaign Number: 21V244
Manufacturer New Flyer
of America, Inc.
Components ELECTRICAL SYSTEM
Potential Number of Units Affected 227
Summary
New Flyer of America, Inc. (New Flyer) is recalling certain 2013-2021 XE40, 2019-2021 XE35, 2018-2021 XE60, 2016-2019 XHE40, and 2015 XHE60 vehicles. Firmware errors in the inverters may cause the electric drive system to shutdown.
Remedy
New Flyer will notify owners, and dealers will update firmware software, free of charge. The recall began on April 19, 2021. Owners may contact New Flyer customer service at 1-204-224-6706. New Flyer’s number for this recall is R21-005.
Notes
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.
INSTRUCTION TO SERVICE
| ITS: 59212 | April 12, 2021 |
| SECTION: | 219-Engine |
| WRITTEN BY: | Dana Carver |
| SUBJECT: | Updating Siemens Software, Vansco and CM0711 Programs |
| ISSUE: | Watchdog faults on the inverters cause them to shut down without warning |
| SUMMARY: | Vansco, CM0711 and Siemens software update |
ITS59212
| Ref. NHTSA Recall No. | Ref. Transport Canada Recall No. |
| 21V-244 | 2021-206 |
THIS ITS DOCUMENT SHOULD BE RETAINED AND REFERRED TO FOR FUTURE MAINTENANCE UNTIL THE NEW FLYER PARTS AND/OR SERVICE MANUAL IS UPDATED TO REFLECT WORK DONE AS A RESULT OF THIS DOCUMENT. ENSURE THAT THIS DOCUMENT IS AVAILABLE FOR PARTS AND MAINTENANCE STAFF GOING FORWARD.
This is to inform you that your vehicle may contain a defect that could affect the safety of a person.
PROCEDURE:
The following are instructions to update the Vansco, CM0711 and Siemens programs on a bus. The programs have been sent to the New Flyer RPSM and must be updated in the order of Vansco, CM0711 and then Siemens.
Vansco Update:
- Ensure the Master Run Switch is in Day/Run position and hazard must be on.
- Connect a laptop with VMM software to the under-dash USB A connector located below the right side of the dash, above the pedals.
- Open the PLC program in the VMM software.
- Select Tools and Query VMMs.
- Ensure you are communicating with all the nodes in the query screen prior to downloading.
- Select Download Logic.
- Ensure the correct file name and revision appear in the File window.
- The software will verify the correct number of VMMs are found. Do not download program if all VMMs are not located. If the correct number of VMMs were found, select Yes.
- After the download is complete, close the download window.
- Disconnect the USB A cable.
CM0711 Update:
- Ensure VMM 7100 or later is installed because it should have Flash Loader v1.9 or newer on it.
- To open flash loader open the VMM software and click Applications → click FlashLoader. See figure 1.
- To check the version is v1.9 or later, click Help → click About. See figure 2.
Figure 1: FlashLoader location
Figure 2: Flashloader version
- Turn hazard lights on, to assure the bus is awake while programming the CM0711.
- Connect a NEXIQ USB LINK to the 9-pin Vehicle Diagnostic Port behind the driver and USB cable to laptop.
NOTE: Make sure the NEXIQ USB LINK is a wired connection (NOT Bluetooth).
- With the NEXIQ connected, in FlashLoader go to File → RP1210 Settings and make sure NEXIQ USB LINK J1939 Channel 1 is selected. Check this if you are having trouble getting connected.
- You will see several question marks and other devices on the left-hand side, find source address 0x49, this is the CM0711 (see figure 3).
- The version shows what is currently loaded in the CM0711. Take a screenshot of what is currently loaded.
- Select the new .vsf file you received and click start (It will take 1-2 minutes to download the program).
Figure 3: CM0711 source address and current version
- After downloading finishes, follow the same process in step 5 and find source address 0x49. The Version # should now be updated to the program you just loaded. The following example in figure 4 is for loading 1019607_NFIL_Electric_Bus_V5.00.vsf. It is also important to notice that it is V5.00 Build 0.
Figure 4: CM0711 source address and updated version
- Turn the master-run switch OFF for at least 20 seconds. It takes at least 7 seconds for the CM0711 to power off after turning off the master-run switch, but 20 seconds is recommended to be safe.
- Put the bus back into Day Run (not EV mode).
- Open the rear panel and make sure the light on the CM0711 is flashing green and then orange. This indicates the CM0711 is operating.
NOTE: If the CM0711 light is off or steady red, it is bricked and will need to be sent back to NPD.
Unfortunately, the bus will be undrivable without a function CM0711 so please contact NPD as soon as possible.
Figure 5: Rear panel and CM0711 module location
- Download updated PLC program to Vansco.
- Remove all tools and debris and return the bus to service condition.
Please refer to Appendix A for Instructions to Update the Siemens Software
Important Note 1: Force the HVIL flag inactive to ensure that the PLC program does not shut off communication prior to searching all nodes (step 1.7 in Appendix A).
Important Note 2: The delay time can be changed to allow the technician more time between key-on and searching for nodes. 15 seconds has been used with success.
Important Note 3: The DICO, motor inverter(s), auxiliary inverters and parameters need to be updated.
Appendix A
1 Instructions
1.1 Use the Siemens Diag in the Rear Panel (see diagram below) to connect the computer containing the software to the system.
Image 1. CAD image showing location of Siemens diagnostic ports
1.2 From the computer, navigate to folder where SW package is located
Image 2. Screenshot showing the contents of the folder with a .hex file (.hex file for XE40 shown in example)
1.3 Start the ELFA WinFlash tool via double click
1.4 From the tool choose Select in Hex-File menu
Image 3. Image showing ELFA flash tool window
1.5 Navigate to the folder where SW package is located ReleasePack→Software→INV. Click the .hex file to open
Image 4. Image showing .hex file for an XE40 configuration
Flash Tool Configuration
Software Flashing
1.6 Switch OFF Key Start (KL15) for all components and wait approximately 30 seconds
1.7 Select Search All Nodes and switch ON Key Start (KL.15)
Image 5. Image showing “Search All Node” selection on Flash tool window
The process of Resetting node(s) will appear like the image below
After successful wakeup, choose the correct Inverter serial number and then click Flash selected nodes.
Image 7. Image showing example of a system containing two Inverters and one DICO
Process of SW flashing is shown below
Image 8. Image showing software flashing in progress
1.8 Once the SW flashing process finished, choose Start program and click OK.
Image 9. Image showing menu that window that appears when flashing is finished
The Inverter with the serial number which has been flashed will show up like the picture below. Close ELFA flash tool.
Image 10. Image showing ELFA flash tool window with serial number of the inverter that has been flashed
2 Validation
Perform a final check for the software version. Refer to Appendix A1 to confirm the software release package for your bus configuration.
3 Error Buffer Check
Once the final check for the software has been installed per the instructions, the user should perform a drive test and export the error buffers to confirm proper functionality of the trap 10 software update. This step only needs to be completed once per bus configuration (e.g. XE40, XE60, etc.). Once the software release package is confirmed for a specific bus configuration, this test will not need to be repeated for every vehicle within that configuration.
1. Key off (restart) the vehicle
2. Test drive the vehicle for 20-30 minutes
3. Pull off to a safe area, stop the vehicle, and turn off bus
4. Connect to the vehicle via PCAN-USB tool (see image below for location of diagnostic port). Open Siadis Expert
Image 11. CAD image showing location of Siemens diagnostic ports
5. Start SIADIS
6. Within Component Selection, choose Motor 1
Image 12. Image of SIADIS tool window showing components
7. Navigate to Utility menu → Software version
Image 13. Image showing SIADIS tool Utility menu
Confirm that the appropriate SW version shows (See Appendix A1)
Image 14. Image showing software version info window (example shown is for an XE40)
8. To access the error buffer select click Utility → “document of error buffers”
Image 15. Image showing to access error buffer in SIADIS tool.
9. Once the error buffers are visible, review them and verify that there are no trap 10 errors
1. If there are no trap 10 errors, mark the vehicle as completed, save the error buffer, and register it as complete in the attached and return a copy to Siemens.
11. If there are trap 10 error in the error buffer, verify that the correct software has been flashed (refer to section 6 & 7) according to Appendix A1
| LABOUR ESTIMATE | ||||
| Operation | Number of Technician(s) | Hours | Labor Time T X HR | |
| 1 | Update the Vansco, CM0711 and Siemens software | 1 | 2 | 2 |
IMPORTANT SAFETY RECALL NOTICE
Subject: Motor Vehicle Safety Recall 21V-244 – Siemens ELFA2 Programming
Dear :
This notice is sent to you in accordance with the requirements of the National Traffic and Motor Vehicle Safety Act.
New Flyer of America Inc. (New Flyer) has decided, that a defect which relates to motor vehicle safety, exists on specific electric drive vehicles equipped with Siemens Industry Inc. (Siemens) model ELFA2 Inverters. This recall is based on information provided by Siemens.
New Flyer has determined that the following vehicles, operated by are affected by this recall action:
Make: New Flyer Heavy Duty Urban Transit Bus
Model: SR2484 – 2021 – XE35 VIN, Unit Number:
Model: SR2485 – 2021 – XE60 VIN, Unit Number:
The Siemens ELFA2 inverter used for both motor power and auxiliary power on the New Flyer electric propulsion system, was found to have a timing issue between the microcontroller and the Static RandomAccess Memory (SRAM). This non-optimum timing causes the inverter to deliver invalid data, resulting in “Trap10” errors. This nuisance error code may cause the electric drive system to shutdown unexpectedly, requiring an ignition reset. The vehicle may then be restarted again once it is brought to a complete stop.
A sudden loss of motive power increases the potential for a vehicle crash and injury.
Siemens has provided New Flyer with new drive system programming which corrects the data timing issue and prevents these nuisance errors. Vehicles which have the newer Siemens ELFA3 inverters are not affected, by this issue.
New Flyer proposes to install this updated programming on the above vehicles at no cost. Please contact your Regional Product Support Manager Lorenzo Mumphery, to coordinate the recall action. New Flyer anticipates that the reprogramming to correct the issue will take approximately 0.5 hours/bus.
If you are a lessor of vehicles which are affected, it is required that any vehicle lessor receiving this recall notice must forward a copy of this notice to the lessee within ten days. If you no longer own this vehicle, or it has been removed from operation permanently, please inform the undersigned.
If you had this corrective action performed before you received this letter, you may be eligible to receive reimbursement for the cost of obtaining a pre-notification remedy of the problem associated with this recall.
If New Flyer is unable to correct this defect within a reasonable time, you may submit a written complaint to the:
Administrator,
National Highway Traffic Safety Administration, 1200 New Jersey Ave. SE,
Washington, DC, 20590,
Or call 1-888-327-4236 (TTY: 1-800-424-9153);
or go to https://www.safercar.gov.
We regret any inconvenience which this action may cause you. However, we are concerned about the safety of your passengers and employees.
Thank you for your attention to this important matter.
Sincerely,
NEW FLYER OF AMERICA INC.
By:
Kerry Legg
Vehicle Safety & Regulatory Compliance Manager
(204) 224-6706
cc:
Scott Halbesma –Vice President, Customer Care
Lorenzo Mumphery – Regional Product Support Manager
21 Affected Products
Vehicles
| MAKE | MODEL | YEAR |
| NEW FLYER | XE35 | 2019-2021 |
| NEW FLYER | XE40 | 2013-2021 |
| NEW FLYER | XE60 | 2018-2021 |
| NEW FLYER | XHE40 | 2016-2019 |
| NEW FLYER | XHE60 | 2015 |
8 Associated Documents
Remedy Instructions and TSB
RCRIT-21V244-0791.pdf 820.634KB
ISSUED Owner Notification Letter(Part 577)
RCONL-21V244-8302.pdf 168.983KB
Defect Notice 573 Report
RCLRPT-21V244-5083.PDF 217.886KB
Recall 573 Report- Amendment 1
RCLRPT-21V244-5420.PDF 217.782KB
Recall 573 Report- Amendment 1
RCLRPT-21V244-7005.PDF 217.782KB
Recall Acknowledgement
RCAK-21V244-9819.pdf 645.764KB
Recall Quarterly Report #3, 2021-4
RCLQRT-21V244-8457.PDF 211.326KB
Recall Quarterly Report #2, 2021-3
RCLQRT-21V244-1314.PDF 211.24KB
Latest Recalls Documents
Heavy Duty Truck Reprogramming
Description:
Designed for flexibility, the USB-Link 3 Wired Edition connects to your PC, tablet, or smartphone with a USB cable, allowing techs to directly connect to a device when working in the field or during signal interruptions.
Built to support the latest protocols (CAN FD, DoIP) and compatible with a wide range of OEM diagnostics software, the USB-Link 3 is our most advanced VCI to date, with the performance and technology you can rely on well into the future.
The USB-Link™ 3 comes with the following:
- Latching USB Cable (PN 404032)
- 9-Pin Deutsch Adapter, 1 Meter (PN 493128)
- J1962 Adapter (16-Pin OBD II, 1 Meter (PN 491113)
The USB-Link™ 3: Wireless is also available (PN 121052).
Specifications
Vehicle Network Protocol Support
CAN FD / J1939 FD / ISO15765 FD - 250K, 500K, 1M b/s with auto baud detection
Single wire CAN (SWCAN)
ISO 11898-3 Fault Tolerant CAN (FTCAN)
Diagnostics Over Internet Protocol (DoIP)
J1708
J1850 VPW (Class 2)
ISO PWM (SCP)
ISO 9141 / KWP2000 (ISO 14230) K/L line
ALDL 9600 and 8192 baud
ATEC 160 baud
Windows® Vehicle Communication API
Windows® Vehicle Communication API
RP1210 a/b/c
J2534 (2004 draft)
J2534-1 partial implementation (commercial vehicle focused)
Operating System Compatibility
iOS
Android™
Windows® 10, 11
Interfaces to Computing Platforms
USB 2.0 (vehicle-to-PC connectivity)
Bluetooth® 2.1 + EDR
Wi-Fi (dual band)
Compatible Software
Detroit Diesel Diagnostic Link
CAT Electronic Technician (On-Highway only)
Cummins Insite
International - ServiceMAXX Fleet Pro
Hino eXplorer
Volvo PTT
VCAD Elite Mack/Volvo
V-MAC Service Tools
Allison DOC® For PC-Service Tool - Protocols Supported: J1939, J1708/J1587, and J1850
Allison DOC® For Fleets (1000/2000) - Protocols Supported: J1939, J1850
Allison DOC® For Fleets (3000/4000) - Protocols Supported: J1939, J1708/J1587
Eaton ServiceRanger
Bendix ACom
WABCO Toolbox
Freightliner ServiceLink
International ABS
International DLB
International Intune
International IPC v2.02
PACCAR DAVIE4
Daimler Truck
DiagnosticLink Order Site:
DiagnosticLink Direct Link:
https://diagnosticlink.nexiq.com/DTNA/Default.aspx
- 🔥🔥🔥2026 New Functions Making X7HD the Top Dog - Big Surprise!!! ANCEL X7HD truck scanner 10 major functional advantages .✅>Full HDOBD/OBD2 Function ✅>ALL System Diagnostic ✅>42+ Reset Function ✅>Active Test / Bi-Directional Control✅>ECU Coding✅>Graphing Live Data✅>Wide Compatibility ✅>2 Yrs Free Update✅>Remote Operation✅>Bluetooth 5.0 & Wifi In addition, 8 major hardware advantages: ✅>6000 mAh✅>10.1 inch Tablet✅>2G RAM✅>32G ROM (Expandable to 128GB)✅>Data Record & Replay & Print✅>Android 10.0✅>Bluetooth 5.0 & Wifi✅>14 Languages
- 🚛OEM DPF Forced Regen & Cylinder Cutout Test & more - ANCEL X7HD diesel scanner diagnostic tool not only supports DPF regeneration, DPF reset, DPF related information reset, DPR state reset, DPD forced regeneration etc, which helps you better solve the exhaust aftertreatment system problems, but also supports activate motor to do exhaust air in ABS Automatically. Moreover, it features TPMS activation, cylinder cut-off and learning functions
- 🚛Advanced ECU Coding & Programming - ANCEL X7HD 10.1inch truck scanner diagnostic tool is equipped with advanced ECU coding, supports Level calibration, Idle speed learning and Adjustment, Camshaft timing control learning, Control unit adaptations, Injector Codes, Read/Write VIN, Road speed limit optional vehicle speed set, etc... PLEASE NOTE that ECU codes are not compatible with all vehicles, please send us your VIN# to check vehicle compatibility
- 🚛42+ Reset Functions & Bidirectional Control - 2026 newest top heavy duty truck scan tool, comes with 42+ special services (ECU, Speed Limit and Idle Reset, Oil Reset, Injector Coding, EPB, ABS, SRS, Suspension, Throttle, etc. and always keep growing), which meet all your various needs for service and maintenance
- 🚛10 Inch All Systems Diesel Scanner & Full HDOBD/OBD2 Modes - ANCEL X7HD diesel truck scan tool supports all systems scan, such as Engine, Brake, Retarder, TECU Transmission, Tachograph, ABS, SRS, TPMS, EPB, SAS, ESP, and other vehicle systems, comes with 10 obd2 service modes: read/erase error codes, Data Stream, I/M Readiness, Vehicle Information, Actuations, DTC Lookup, EVAP, view freeze frame, etc
- Dealer-Level Diagnostics, Faster & Easier: The heavy duty truck scanner delivers full-system diagnostics for engine, ABS, transmission, and more, plus 7+ reset functions like DPF Regen and Speed Limit Adjust. Powered by a 1.3G CPU, 2GB RAM, 16GB storage, Android 8.1, and a 3000mAh battery, it runs smoothly for fast scanning, live data, reports, Auto VIN, Wi-Fi updates, and easy handheld use. It captures screenshots, replays live data, and generates reports to support your repair decisions.
- Diesel Truck DPF Regen & Reset Features: Experiencing loss of power, sluggish acceleration, or poor hill-climbing performance? These symptoms are often caused by a clogged or overloaded DPF. The truck diagnostic scanner offers OEM-level forced DPF regeneration, DPF reset, and DPD/DPR functions. This device extends DPF lifespan and efficiently diagnoses exhaust aftertreatment issues. It can significantly reduce diagnostic time and save you up to $3,000 or more in costly dealership fees.
- 7+ Resets - Perform Essential Procedures: The truck scanner features 7+ essential resets including DPF Regen clears carbon buildup; Oil Reset clears service light; Injector Coding matches new injectors; DEF Test checks urea injection; Speed Limit Adjust saves fuel; Cylinder Cutout pinpoints misfires; Clutch Relearn restores smooth engagement. Reset after maintenance or part replacement for proper truck operation. Vehicle compatibility varies. Email [email protected] to confirm before buying.
- One Tool for 50+ Truck Brands: The diesel scanner supports J1939, J1708, J1587, and OBD2/CAN protocols, delivering broad coverage for major diesel trucks and commercial vehicles including Cummins, Cat, Detroit, Paccar, Volvo, Freightliner, Kenworth, Peterbilt, International, Mack, Isuzu, Hino, Scania, Mercedes-Benz, and more. Also supports Allison, Aisin, Eaton, WABCO, and Bendix, helping you diagnose more vehicles, reduce equipment costs, and handle more jobs with one professional scan tool.
- Full System Diagnostic for Truck: The truck scanner diagnostic tool covers all systems like engine, ABS, transmission, SAS, SRS, TPMS and more. It reads fault codes and shows real-time data. Additionally, it includes full HD OBD and OBD2 modes: read/clear codes, live data stream, I/M readiness, freeze frame, DTC lookup, and more. When warning lights appear or performance issues arise, quickly identify which system is affected and gain the real-time data needed for accurate diagnosis.
- Diagnose Heavy-Duty Truck Problems Fast — Read and clear fault codes and diagnose warning light issues on many Class 4–8 diesel trucks including Freightliner, Peterbilt, Kenworth, Volvo, Mack and Cummins-powered vehicles
- Help Reduce Downtime & Repair Costs — It offers full system diagnostics for major trucks meeting standard protocols, along with complete OBD2 functionality. Quickly check engine faults, view live truck data and identify issues before expensive repair shop visits or unnecessary repairs
- No complicated setup required — Simple menus and built-in DTC explanations make this truck code reader easy to use for owner-operators, mobile mechanics and small fleet maintenance
- Live Data & Built-in DTC Lookup — View real-time engine data and built-in truck fault code definitions directly on the scanner to help understand vehicle problems faster without searching through manuals
- Free Lifetime Updates & Technical Support — Includes free software updates plus responsive technical support for setup, compatibility and everyday truck diagnostics
- 【Built for Heavy Duty Diesel Diagnostics】Designed for SAE J1939 and J1708 compliant trucks, buses, and diesel-powered commercial vehicles. HD601 truck scanner diagnostic tool helps owner-operators, small fleets, mobile technicians, and independent repair shops quickly identify fault codes, view live data, and make informed repair decisions—saving time, reducing downtime, and avoiding unnecessary shop visits
- 【Full System Diagnostics+All HD OBD Modes】The New HD601 heavy duty truck scanner delivers full-system diagnostics on SAE J1939 and J1708-compliant commercial vehicles—digging into engine, transmission, ABS, fuel, every system that keeps your rig rolling. It supports all HD OBD modes, giving you live data, freeze frame, ECU info, vehicle info, emissions data tracking, plus code reading and clearing. Not just what broke, but why—so you fix it right the first time. Pinpoint issues faster, cut repair costs, and spend less time on the shoulder
- 【Wide Heavy-Duty Vehicle Coverage】Supports a wide range of heavy-duty vehicle manufacturers and systems, including Freightliner, Kenworth, Peterbilt, Volvo, International, Detroit, Cummins, Paccar, Allison, Eaton, Bendix, Wabco, and more. Coverage varies by vehicle make, model, year, and system configuration. Contact our support team before purchase if compatibility verification is needed
- 【Speaks Major Truck Protocol】The New HD601 diesel truck scanner is built for American-made trucks—and supports the heavy‑duty protocols you' re most likely to run into on the road: SAE J1939, J1708/J1587, ISO 15765‑4, ISO 14230‑4, ISO 9141‑2, J1850 PWM/VPW, ISO 27145‑4, and EURO‑6. For most trucks, model years, and systems, it speaks the language your vehicle understands. Just plug it in and start diagnosing—no guesswork, no gatekeeping. Note: vehicle functions and module availability may vary by manufacturer and model year
- 【Save Hundreds on Diagnostic Fees】Why pay $150–300 for someone to read your codes? With the New ANCEL heavy duty truck scanner, you can pull fault codes yourself—in minutes, without leaving the truck. One or two uses pays for the tool. After that, every diagnostic is money back in your pocket. Smart investment for owner-operators, techs, and small fleets. Read and clear stored fault codes in minutes. Active fault codes may require repairs before they can be cleared
- 2026 LAUNCH 1st Advanced Scan Tool Compatible With 12V&24V Vehicles:Design for Passenger&Commercial Vehicles 2 in1,work for Cars/Trucks/buses/trailers/excavators/diesel engine/pick-up/etc.
- J2534 Protocols with Smartlink C:Advanced OEM J2534 code ,Helps access direct data online, replace existing software/firmware in ECU,code new ECUs and fix software-controlled issue.
- Over 60 Service Reset Functions + Bi-Directional + ECU Code:This scan tool can support ECU Code,60+ reset service functions like SAS/EPB/TPMS/DPF/Oil/Brake/ABS Bleed, Injector coding, etc.
- Advanced Hardware & All Systems Diagnosis+Topology Display:Support All systems Diagnostic including ENG, AT, ECM, TCM, ABS, SRS, BCM, BMS, TPMS, SAS, Fuel System, Light System and more.
- Wider Vehicle Coverage of 12V & 24V Vehicles + 24 Languages: LAUNCH X431 PRO3S+SMARTLINK HD automotive scanner is ALL-IN-ONE Scan Tool for 12V cars and 24V Heavy-duty trucks support CANFD & DOIP.
- 【WIRELESS DIESEL DIAGNOSTICS FROM YOUR PHONE】Turn your smartphone into a portable heavy-duty truck scanner in seconds. The ANCEL HD100 lets you read and clear fault codes, monitor live data, check engine health, and perform diesel diagnostics directly through the ANCEL Trucker App. Simply plug into the 9-pin or 16-pin port, pair via Bluetooth, and diagnose your truck from the cab, roadside, fleet yard, or repair shop—without carrying bulky diagnostic equipment
- 【RUN DPF REGEN WITHOUT DEALER STOPS】Handle common DPF issues before they turn into costly downtime. The HD100 supports DPF regeneration, DPF reset, and soot-related diagnostics on compatible Cummins and Caterpillar engines. Follow guided app instructions directly from your phone to start the procedure, monitor regeneration status in real time, and help reduce unnecessary service visits. NOTE: Not compatible with pickup trucks
- 【COMPACT BLUETOOTH TRUCK SCANNER FOR DAILY USE】Designed for drivers who want fast diesel diagnostics without bulky equipment or extra cables. The pocket-size HD100 quickly connects to iPhone and Android devices, allowing you to check warning lights, engine faults, ABS status, transmission systems, and other supported modules. Keep it in your cab or toolbox for quick roadside diagnostics, preventive maintenance, and everyday truck health checks
- 【FULL-SYSTEM DIAGNOSTICS FOR MAJOR DIESEL TRUCKS】Access engine, ABS, transmission, and other supported systems on Freightliner, Kenworth, Peterbilt, Volvo, Mack, International, and more. Read and clear fault codes, view live data, and monitor real-time system information across major diesel engines and components, including Cummins, Caterpillar, Detroit, Allison, Bendix, Eaton, and Wabco. Supports SAE J1939 and J1708 protocols
- 【NO SUBSCRIPTION FEES & LIFETIME FREE UPDATES】The ANCEL Trucker App provides fast Bluetooth pairing, DTC Lookup, live data viewing, and diagnostic reporting with no subscription fees, activation charges, or recurring costs. Rugged lock-ring connectors help maintain stable communication on vibration-prone diesel trucks, while lifetime free updates continue improving compatibility, functionality, and long-term value for owner-operators, drivers, and fleet maintenance teams
Last update on 2026-05-23 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.