BlueTEC EMP Software Update – 2014-2016 Freightliner Sprinter

SEOCONTENT-STARTGroup 54
Campaign: 2021070034
CODE: NC3ID182ND
SM54.21-D-0242SG
07.30.2021
SM54.21-D-0242SG Update control unit software (code:
NC3ID182ND, acc. no.: 07 972 82)
07.30.2021
Warranty Information
g Check
1 Check whether vehicle is affected
by Campaign.
i
Check Vehicle Master Inquiry (VMI)
in Netstar to verify Campaign is
open.
i
The Emissions Campaign that we
recently conducted on your vehicle
(see Vehicle Master Inquiry (VMI) in
Netstar) has not yet run its full
course. This new measure will
ensure that the Emissions
Campaign is conducted correctly
and completely.
a
Damage
Code
Operation
No.
Time Operation Text
07 972 82 02 2443 0.1 hr Connect/disconnect vehicle diagnosis system
02 2445 0.1 hr Connect/disconnect charger (vehicle diagnosis system connected)
02 2442 0.1 hr Update … Control unit software (vehicle diagnosis system connected)
02 2457 0.2 hr Extra work for: Update …. control unit software with increased data volume
Campaign 2021070034
SM54.21-D-0242SG | Van | 07.30.2021 1
Update software
2 Connect charging equipment.
A 000 588 00 81 00 Charger WS54.00-P-0037B
p
During the entire work procedure a
sufficient voltage supply must be
provided for the vehicle’s on-board
electrical system.
Otherwise any undervoltage that
occurs may damage the control
units.
i
Follow the operating instructions
for the charger.
i
Use the charger to ensure that an
adequate power supply (min.
12.5 V) is provided for the onboard
electrical system battery.
3 Connect diagnostic system.
a AD00.00-D-2000-04SD
i
Always use the latest XENTRY
Diagnosis software release with all
available addons.
i
It is absolutely essential to
precisely follow the operation steps
as described in the vehicle
diagnosis system.
i
If there are questions or
problems with carrying out the
service measures described
here, create a ticket in the
XENTRY Support & Feedback
(XSF) system under the
“XENTRY Diagnosis” or “Parts”
tab.
a Campaign 2021070034
SM54.21-D-0242SG | Van | 07.30.2021 2
4 Update software for control units
through special procedure
(“Exhaust aftertreatment” service
measure).
p
The measure must only be
performed using the described
special procedure (“Exhaust gas
aftertreatment” service measure).
Other procedures are not
permitted.
Otherwise correct running of
control unit programming cannot
be guaranteed.
i
OM642 engine: select the following
menu items (also see picture
below):
Control units view →
N3/35 – Engine electronics ′CDI60′
for combustion engine ′OM642′
(CDI) (Code: MH3|MH5|MH7) →
Special procedures →
Service measure “Exhaust
aftertreatment” →
Perform ′Exhaust aftertreatment′
service measure.
i
OM651 engine: select the following
menu items (also see picture):
Control units view →
N3/33 – Engine electronics ′CDI43′
for combustion engine ′OM651′
(CDI) (Code: MH5|MH8) →
Special procedures →
Service measure “Exhaust
aftertreatment” →
Perform ′Exhaust aftertreatment′
service measure.
i
XENTRY Diagnosis guides you
through the process of the
measure. The operation steps in
XENTRY Diagnosis must be
complied with completely until the
Service measure “Exhaust
aftertreatment” results page is
displayed and uploaded to pXD.
i
Invoicing must be based on the
operation items in this new
measure (see above), in
accordance with the operation
steps in this measure.
5 Remove vehicle diagnosis system.
a AD00.00-D-2000-04SD
a
6
A
Remove charger from vehicle.
000 588 00 81 00 Charger WS54.00-P-0037B
Campaign 2021070034
SM54.21-D-0242SG | Van | 07.30.2021 3
OM642 engine: Exemplary screenshot of Exhaust Aftertreament Service Measure
D54.00-A009-79
D54.00-A010-79
OM651 engine: Exemplary screenshot of Exhaust Aftertreament Service Measure
a Campaign 2021070034
SM54.21-D-0242SG | Van | 07.30.2021 4

SEOCONTENT-END