| “This site contains affiliate links for which OEMDTC may be compensated” |
August 17, 2021 NHTSA CAMPAIGN NUMBER: 21E075000
Improperly Crimped Lifting Cable
An improperly crimped cable may come out of place during a lifting operation, possibly causing the generator set to fall, increasing the risk of injury.
NHTSA Campaign Number: 21E075
Manufacturer Cummins
, Inc.
Components EQUIPMENT
Potential Number of Units Affected 29
Summary
Cummins, Inc. (Cummins) is recalling certain generator sets, model 6RBAB, 10RBAB, 15RBAB, and 8RBAB. The lifting cables may be improperly crimped.
Remedy
Dealers will inspect the lifting cable, and either replace the cable, or install a warning label, free of charge. Owner notification letters were mailed October 8, 2021. Owners may contact Cummins’ customer service at 1-800-286-6467. Cummins number for this recall is 4495.
Notes
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.nhtsa.gov.
Technical Service Bulletin
| Technical Service Bulletin: TSB210146 | Released Date: 13-Sep-2021 |
| Safety Campaign #4495 RBAB Lift Cable Crimp Issue | |
Safety Campaign #4495 RBAB Lift Cable Crimp Issue
Warranty Statement
The information in this document authorizes specific changes to the repair practice for failures covered under product warranty coverages.
Contents
Product Affected
RBAB Spec G
Issue
Symptom:
- Lifting cable around the alternator may be improperly crimped and unable to carry its rated weight, which condition may cause the cable to fail during lifting.
Root Cause:
- Cable supplier quality issue with crimping tool.
Verification/Confirmation
If the unit has one of the serial numbers listed below, the unit needs to be inspected for uncrimped cable ferrules. If the cable ferrules do not have a marking on them to show it has been crimped, (see arrows in Figure 1 below) the cable needs to be replaced.
Figure 1, Cable Markings
Table 1, Serial Number
| A210866229 | B210891579 | D210915365 |
| A210866230 | C210891527 | D210915366 |
| A210866231 | C210891528 | D210915367 |
| A210867286 | C210900416 | D210919566 |
| B210875016 | C210902316 | D210919567 |
| B210875018 | C210904096 | D210919600 |
| B210891526 | D210906237 | E210919559 |
| B210891556 | D210906240 | E210919561 |
| B210891576 | D210909137 | E210919562 |
| B210891577 | D210915363 | |
| B210891578 | D210915364 |
If the unit is found to have one of the above serial numbers, follow the below steps in the resolution to inspect and/or replace the cable.
Note: This issue has been resolved by the supplier. New cables and generator sets outside of this serial number list do not have ferrule crimping issues.
Resolution
Warning: Ensure Engine is off and generator set is not connected to a power source to prevent accidental running of the generator set.
Warning: Wear the appropriate PPE to protect worker while performing this repair.
Warning: The generator set is over 90 kg (200 lbs). Use caution when lifting.
Warning: Do not use the lifting eye cable to lift the unit. Use an alternative method.
1. If installed, lift unit out of vehicle using 4 lifting holes on each side. Do not use lifting eye cable
Figure 2, Lifting Unit
2. Remove front enclosure panel.
Figure 3, Front Panel Removed
3. Remove left side enclosure panel and grate.
Figure 4, Side Panels Removed
4. Remove top two small enclosure covers.
Figure 5, Top Panels Removed
5. Inspect the cable ferrules for the marking to see if the unit’s cable is properly crimped. The cable can also be visually inspected for a crimped cable.
Figure 6, Uncrimped vs. Crimped
Note: If cable has no crimp marking, continue to follow the steps below and replace the cable. If cable is marked (and properly crimped), no repair is required. Replace enclosure panel.
Note: To order replacement cable, see ‘Service Instructions’ section below.
6. Remove right side enclosure panel and cut cable tie to slide wire leads through enclosure panel
Figure 7, Right Side Panel Removed
7. Remove only the left side ring terminals in control box. Do not lose the two jumper wires.
Figure 8, Left Side Ring Terminal Disconnect
8. Cut cable ties on alternator output leads.
Figure 9, Remove cable Ties
9. Unplug two blue fast-on connectors.
Figure 10, Unplug fast-on connectors
10. Disconnect brush block connectors.
Figure 11, Disconnect Brush Block Connections
11. Remove chassis ground connections.
Figure 12, Chassis Ground
12. Remove Control box.
Figure 13, Remove Control Box
13. Disconnect hydraulic pump connector.
Figure 14, Disconnect Pump Connection
14. Push coolant temp sensor through control grommet.
Figure 15, Coolant Temperature Sensor
Warning: Confirm unit is still disabled to ensure fan does not accidentally spin
15. Remove fan shroud and fan mounting bolts. Fan and shroud come off together
Warning: Make sure engine driving hydraulic fluid is off and the lines are not pressurized before removing
16. Remove secondary fan bolt.
17. Use puller to remove fan
Figure 18, Fan Puller
Warning: Make sure engine driving hydraulic fluid is off and the lines are not pressurized before removing
18. Remove hydraulic hose.
Figure 19, Remove Hose
19. Remove hose coupler connection on hydraulic pump.
Figure 20, Remove Hose Coupler
20. Remove pump.
Figure 21, Remove Pump
21. Remove the 4 alternator mounting bolts.
Figure 22, Remove Mounting Bolts
Warning: Alternator weighs over 75 lbs. Use caution when lifting.
Warning: Do not use the lifting eye cable to lift the unit. Use an alternate lift method
22. Lift with rated lifting strap and remove alternator from base pan. Do not use lifting eye cable.
Figure 23, Lift Alternator
23. Remove bolt and grommet bracket.
24. Remove brush blocks.
Figure 25, Brush Block Removal
25. Tilt alternator up and set on pump end with shaft pointing up.
26. Remove 4 bolts holding on alternator end.
Figure 26, Alternator Orientation
27. Remove alternator end. Do not cut or strip output wire insulation.
Figure 27, Lift Off Alternator End
28. Slide off old cable.
Figure 28, Remove Old Cable
Installation of New Cable
1. Install new cable
Figure 29, Install New Cable
2. Feed wires through alternator end and line up bolt holes.
Figure 30, Install Alternator End
3. Install 4 mounting bolts with washers to alternator.
4. Make sure all vibration isolators are installed and oriented correctly.
Figure 31, Vibration Isolator
5. Tilt alternator and set on 4 mounting isolators.
6. Reinstall wire grommet bracket. Make sure it is seated completely and flush.
Figure 32, Seated and Flush
7. Reinstall 2 pump bolts by hand first. Then torque to 58 Nm.
Figure 33, Pump Bolt Installation
8. Test fit plastic fan to ensure it spins freely with no interference.
Figure 34, Test Fit Fan for Interference
9. Reinstall brush blocks, ensure bolt C clip is installed.
Figure 35, Brush Block Installation and C-Clip
10. Reinstall hose coupler to pump. Torque to 97 Nm.
Figure 36, Hose Coupler Installation
Warning: Alternator weighs over 34 kg (75 lbs). Use caution when
11. Lift alternator and reinstall alternator in base pan, torque bolts to 46 Nm.
Figure 37, Lift and Install Alternator
12. Reinstall fan, torque to 58 Nm using fan holder
Figure 38, Hose Installation
13. Reinstall fan, torque to 58 Nm using fan holder
Figure 39, Fan Holder
14. Reinstall fan and shroud.
Figure 40, Install Fan and Shroud
15. Push side panel over pump inlet. Do not install panel bolts yet (see step 20).
16. Reinstall coolant temperature sensor through control grommet and connect pump connector.
17. Reinstall control
Figure 41, Install Control Box
18. Push generator output wire leads through side panel.
Figure 42, Output Wire Leads
19. Feed the 7 wire connectors through the side panel. Install wire holder and twist up into opening.
Figure 43, Wires Through Grommet
20. Install side panel bolts.
Figure 44, Side Cover Installation
21. Install wire jumpers to bottom terminal.
Figure 45, Jumper Connections
22. Install chassis ground connections (green jumper, silver strap and white with blue ring terminal).
Figure 46, Ground Connection
23. Install brush blocks (Wire F1 on the left, Wire F2 on the right).
24. Connect two blue fast-on connectors.
25. Run J1 through top current transformer loop.
Figure 47, J1 Through Top CT
26. Run J4 through bottom current transformer loop.
Figure 48, J4 Through Bottom CT
27. Take black wire and J4 and install to second from bottom terminal.
28. Take wires T3, T2, and jumper wire TB1-2 TB1-4 and install to third from bottom terminal.
29. Take orange wire and T1 and install in top terminal
Figure 49, Wire Locations
30. Push wires inside base pan and install 3 cable ties.
Figure 50, Wire Securing
31. Install enclosure make sure mesh grate is behind tab.
Figure 51, Enclosure Tab
32. Reinstall side panel and grate.
33. Reinstall top two enclosure panels.
34. Reinstall front enclosure panel.
Service Instructions
Campaign Filing Instructions:
Fail Code: JSLIML
Account Code: 65
Authorization Code: 4495
Applicable SRT’s:
00-901: 0.7 hours- Administrative time (shop)
99-999: 1.0 hours Inspect cable ferrules
25-3AG: 5.1 hours cable replacement
Parts: Email: cpgf.customer.quality@cummins.com to order a replacement cable. In the email please provide the model and serial number of the unit being repaired, and the attention and address of where to ship the cable.
Travel: If travel to customer site is necessary, travel allowed else follow in-shop repair procedures and claims filing.
Expiration Date: None
Document History
| Date | Details |
| 2021-7-8 | Module Created |
| 2021-9-10 | Non-Product Problem Solving (PPS) |
| 2021-9-13 | Non-Product Problem Solving (PPS) |
Last Modified: 13-Sep-2021
*** IMPORTANT SAFETY RECALL***
NHTSA Recall No. 21E-075
Cummins Campaign #4495
October 8, 2021
Dear Cummins Customer:
This notice is sent to you in accordance with the requirements of the National Traffic and Motor Vehicle Safety Act.
Cummins Inc. has decided that a defect which relates to motor vehicle safety exists in certain 6RBAB, 8RBAB, 10RBAB, 15RBAB generator sets that were manufactured between January 29, 2021 and May 13, 2021.
This notice applies to your 6RBAB, 8RBAB, 10RBAB, or 15RBAB generator set(s) listed in the table on the enclosed Generator Set serial number list.
WHY IS A RECALL BEING CONDUCTED?
The generator sets are equipped with lifting cables to be used during product assembly, installation, service or removal. The ferrule on the genset lifting cable may have been improperly crimped by the supplier. If this condition exists, the lifting cable may pull out of the ferrule during lifting operation, which may cause the genset to fall during assembly, installation, service or removal, possibly resulting in personal injury.
WHAT ARE WE DOING ABOUT THE PROBLEM?
Cummins has released field Safety Campaign #4495 RBAB Lift Cable Crimp Issue to correct this condition by inspecting the lifting cable and, if defective, replacing it with a properly crimped lifting cable. Repair parts are currently available at Cummins Distributors and authorized Warranty Dealers. The repair will be completed free of charge and most applications will require approximately 7 hours to complete.
WHAT SHOULD YOU DO?
If the generator set must be lifted or moved, DO NOT use the lifting cable until it has been inspected as part of this campaign. Instead, use an alternative method for lifting until the lifting cable can be inspected and, if necessary, replaced with a properly crimped lifting cable.
Contact the nearest Cummins Distributor or authorized Warranty Dealer to arrange to have this campaign performed on your generator set. The distributor or dealer will work with you to schedule the best date to complete this repair.
Federal law requires vehicle lessors receiving this recall notice to forward a copy of this notice to the lessee within ten (10) days. Also, it is a violation of Federal law for a dealer to deliver a new vehicle or equipment covered by this recall notice under a sale or lease until the defect has been remedied.
WHO SHOULD YOU CONTACT IF YOU HAVE FURTHER QUESTIONS OR CONCERNS?
If you have questions or concerns about this recall, please contact your local Cummins Distributor or authorized warranty dealer. You may also contact Cummins Care at 1-800CUMMINS (1-800-286-6467) or visit our website at care.cummins.com.
If you have a complaint relative to this recall, you may report it to the following:
Administrator
National Highway Traffic Safety Administration
1200 New Jersey Avenue, SE
Washington, DC 20590
You may also call the toll-free Vehicle Safety Hotline at 1-888-327-4236 (TTY: 1-800-424-9153); or go to https://www.safercar.gov.
If you are no longer the owner of the generator set(s) listed in the table below, please forward this notice to the new owner or provide the new owner’s contact information to Cummins so that we can notify them of this recall.
Cummins is taking this action in the interest of safety and satisfaction with our products. We apologize for any inconvenience and thank you for your attention to this matter.
Sincerely,
Campaign Administrator Cummins Inc.
*** IMPORTANT SAFETY RECALL ***
NHTSA Recall No. 21E-075
Month XX, YYYY
OEM Customer
XXXX Street Address
City, ST 12345-6789
Dear Cummins OEM Customer:
We are writing to inform you that Cummins Inc. has determined that a safety-related defect exists in certain 6RBAB, 8RBAB, 10RBAB, 15RBAB generator sets that were manufactured between January 29, 2021 and May 13, 2021. Cummins has initiated a recall of the subject generator sets. Our records indicate that some of these generator sets have been shipped to you.
A copy of Cummins’ initial Part 573 Defect Notification report is enclosed. This notification was submitted to the National Highway Traffic Safety Administration (NHTSA) on August 17, 2021. As more fully described in the Defect Notification, certain generator sets are equipped with lifting cables to be used during product assembly or installation. The ferrule on the generator set lifting cable may have been improperly crimped by the supplier.
Enclosed is a list of generator set serial numbers for affected generator sets that our records indicate were shipped to your locations. For generator sets that have left your control, we encourage you to make a safety defect determination in accordance with 49 USC 30118 et seq. and, as appropriate, to submit a Defect Notification to NHTSA in accordance with 49 CFR Part 573. Cummins will conduct the recall, including notifying owners pursuant to 49 CFR Part 577, performing the remedy, and submitting quarterly status reports to NHTSA. Cummins is requesting that you provide the associated vehicle model identification, VINs and owner contact information to facilitate owner notification. Please work with your Cummins account team leader to ensure that the requested information is provided to Cummins as soon as possible.
For generator sets that are still in your inventory, please contact your local Cummins Distributor to arrange for this repair. Generator sets can be repaired under TSB210146.
Please note that Federal law prohibits delivery of these generator sets, or vehicles equipped with these generator sets, under a sale or lease until this condition has been remedied.
Cummins apologizes for this inconvenience, but we are initiating this action in the interest of our customers’ safety and satisfaction with our products. Thank you for your assistance.
Please confirm receipt of this communication.
Sincerely,
Account Manager
Enclosures:
1 Affected Product
Equipment
| BRAND | PART NO. | PRODUCTION DATES |
| CUMMINS | GENSET | |
7 Associated Documents
Defect Notice 573 Report
RCLRPT-21E075-7255.PDF 217.178KB
Loading...
Reload document 
Open in new tab
Recall Acknowledgement
RCAK-21E075-1003.pdf 645.749KB
Loading...
Remedy Instructions and TSB
RCRIT-21E075-6867.pdf 16726.413KB
Loading...
ISSUED Owner Notification Letter(Part 577)
RCONL-21E075-7670.pdf 110.456KB
Loading...
Noncompliance Notice 573 Report
RCLRPT-21E075-9733.PDF 217.178KB
Loading...
Recall Quarterly Report #1, 2021-4
RCLQRT-21E075-6980.PDF 211.117KB
Loading...
Manufacturer Notices(to Dealers,etc)
RCMN-21E075-9289.pdf 133.339KB
Loading...
Latest Recalls Documents
- EFFICIENT CHARGING: Use the adapter included in the package to charge the power station from 0 to 80% in 2hrs, and use the this power supply to charge other devices at the same time while charging, which could be equivalent to a charging strip , improving the efficiency of uses. It can be charged efficiently with MARBERO's dedicated 30W or 60W solar panel, suitable for outdoor or backyard camping
- COMPACT & PORTABLE DESIGN: Super slim size(6.5 x 4.6 x 3.1 inches), the portable power station is about the size of a basic DSLR; With the strong yet lightweight(3.2lbs) plastic case, plus an ergonomic handle, it's quite suitable for outdoor camping, road trips, backyard camping, home, school, office,etc.
- MULTI-OUTPUT: There are 8 output ports could be used at the same time, and the built-in BMS system ensures stability and safety. The car DC charger output cable(included) will supply power to car fridge, vacuum cleaner, and air compressor. USB and USB C PD ports are compatible for all the mobile phones(1hr full), tablets(1.5hrs full), laptops(2hrs full), it's an essential unit for road trips. The two AC output ports will power home appliances, such as small TVs, game consoles, projectors, etc.
- BRIGHT LIGHTS: With three levels of brightness, the portable power bank can be used as a professional flashlight when needed, which is very suitable for use when the car breaks down, power outage at home, or a tent power supply. The 1st level can be used for 68hrs(light up a small room), the 2nd level can be used for 48hrs(lighting for walking at night), and the 3rd level can be used for 37hrs(light up the living room). There is SOS mode, use the international SOS frequency for help.
- SECURED & ASSURED: The Battery Management System (BMS) allows for voltage control, temperature control and more advanced safety operations. Designed with the cooling vents on the back to help this portable power supply keep the temperature constant, its internal electrical elements will not be damaged by high temperatures. When it comes to short circuit or overload, it automatically shuts off the power to protect itself and the powered devices.
- With 13,000 watts of power, the XP13000EH Dual Fuel generator will keep your whole home running during a storm or power outage
- DuroMax is the industry leader in Dual Fuel portable generator technology, with a full assortment ranging from digital inverters to generators that can power your entire home
- At the core of all our products resides a robust DuroMax engine. Designed for Power. Designed to Last
- The XP13000EH comes with a push button start, a front facing interface that allows you to change your fuel type in seconds, and a wide variety of outlets (including a transfer switch-ready 50 amp outlet)
- Constructed with a heavy-duty all metal frame and power panel - No plastic parts
- 9500 Running Watts and 12500 Peak Watts (Gasoline); 8500 Running Watts, 11200 Peak Watts (Propane); Remote Start With Included Key Fob, Electric and Recoil Start; Up to 12 Hours of Run Time on a 6. 6 Gallon Fuel Tank With Fuel Gauge
- Features Two GFCI 120V 5–20R Standard Household Receptacle, One Transfer Switch Ready 120V L14-30R, and One RV Ready 120/240V 14–50R; All Outlets Have Rubber Covers for Added Safety
- Powered by a Heavy Duty 457cc Westinghouse 4-Stroke OHV Engine Featuring a Long-Lasting Cast Iron Sleeve With Automatic Low Oil Shutdown and Digital Hour Meter. VFT display gives you real time updates with the voltage output, frequency, and lifetime hours
- Plug-and-Play: Comes With a Remote Start Key Fob, 12V Battery Charger, Oil, an Oil Funnel, a Tool Kit, and a User’s Manual to Get You Started Right Out of the Box (Minimal Assembly Required)
- All Westinghouse Portable Generators are Functionally Tested in the Factory and May Contain Minimum Residual Oil and/or Fuel Odor; EPA Compliant; Backed By 3-Year Limited Service, Labor, and Parts Coverage and Nationwide Customer Service Network
- Keep your family safe with 5600 starting watts and 4500 running watts of power
- Electric start functionality turns the 224cc engine on with the press of a switch
- The WEN Watchdog CO Shutdown Sensor helps protect both you and your family by automatically turning off the generator if dangerous levels of carbon monoxide are detected
- 4.3-gallon gas tank provide up to 12.5 hours of half-load run time
- Includes a wheel kit, two standard 120V 5-20R 20-amp outlets, one RV-ready 120V 30-amp TT-30R outlet, one transfer-switch-ready 120V 30-amp NEMA L5-30R twist lock receptacle, and a three-year limited warranty
- 149cc engine generates up to 3600 surge watts and 2900 rated watts
- Produces clean power to prevent damage to sensitive electronics such as smart phones, tablets and laptops
- Ultralight body weighs in at a mere 46 pounds for easy transport and torage
- Fuel shutoff maximizes the generator’s lifespan by using up the remaining fuel in the carburetor before shutting down
- Includes two three-prong 120V receptacles, one TT-30R RV receptacle, one 12V DC receptacle, two 5V USB ports, and a three-year warranty
- Perfect as a backup power source for larger homes or a dependable source of portable power
- 14,500 peak watts, 11,500 running watts (gasoline); 13,500 peak watts, 10,500 running watts (propane); 12,000 peak watts, 9,500 running watts (natural gas)
- Runs for up to 19 hours on a 9.5 gal. fuel tank with built-in fuel gauge; up to 7 hours on a 20 lb. propane tank
- Powered by a heavy duty 550cc 4-Stroke OHV Westinghouse Engine constructed with a durable cast iron sleeve
- All Westinghouse Portable Generators are Functionally Tested in the Factory and May Contain Minimum Residual Oil and/or Fuel Odor; EPA Compliant; Backed By 3-Year Limited Service, Labor, and Parts Coverage and Nationwide Customer Service Network
- 3600 Running Watts and 4650 Peak Watts; Recoil Start; 4 Gallon Fuel Tank With Fuel Gauge; Up to 14 Hours of Run Time Per Tank
- Feature Two 5–20R 120V Household Duplex Receptacle, One RV-Ready TT-30R 30 Amp Receptacle, and One L5-30R 30 Amp Receptacle; All Outlets Have Rubber Covers for Added Safety
- Plug-and-Play: Comes With Oil, an Oil Funnel, a Tool Kit, and a User’s Manual to Get You Started Right Out of the Box (Minimal Assembly Required)
- Powered by a 212cc Westinghouse 4-Stroke OHV Engine Featuring a Long-Lasting Cast Iron Sleeve With Automatic Low Oil and Carbon Monoxide (CO) Shutdown
- All Westinghouse Portable Generators are Functionally Tested in the Factory and May Contain Minimum Residual Oil and/or Fuel Odor; EPA Compliant; Backed by 3-Year Limited Service, Labor, and Parts Coverage with Nationwide Customer Service Network
- At less than 49 pounds, this inverter is one of the lightest 4000-watt inverters in the industry
- 64 dBA from 23 feet is perfect for camping, tailgating or to backup a few home essentials, with 4000 starting watts, 3000 running watts and up to 10 hours run time, plus features CO Shield carbon monoxide auto shutoff system
- The optional parallel kit enables this inverter to connect with another 4000-watt Champion inverter to double your output power
- Includes a 120V 25A TT-30R outlet, a 120V 20 A household duplex outlet (5-20R) with clean electricity (less than 3% THD), plus a 12V automotive-style outlet, and Parallel outlets
- Includes 3-year limited warranty with FREE lifetime technical support from dedicated experts
- 224cc engine generates up to 4800 surge watts and 4000 rated watts
- Produces clean power to prevent damage to sensitive electronics such as smartphones, tablets and laptops
- Ultra-efficient 1.9-gallon tank provides up to 7 hours of half-load run time
- Fuel shutoff maximizes the generator’s lifespan by using up the remaining fuel in the carburetor before shutting down
- Includes onboard wheels, a telescoping pull handle, four three-prong 120V receptacles, one TT-30R RV receptacle, one 12V DC receptacle, two 5V USB ports, and a three-year warranty
- Switch between gasoline (14500 surge watts, 11500 running watts), propane (12500 surge watts, 10300 running watts), and natural gas (10500 surge watts, 8750 running watts) with a simple turn of the selection dial
- Operates at 120V and 240V, making it perfect for transfer switches and emergency backup
- Electric start powers the 500c 4-stroke OHV engine with the turn of a key
- 8.2-gallon tank provides up to 12 hours of half-load runtime
- Includes four 120V 5-20R outlet, a 120V/240V transfer-switch-ready NEMA L14-30R outlet, a 120V/240V transfer-switch-ready NEMA 14-50R outlet, a 12V DC automotive outlet, a bottle of oil, a 6-foot LPG connection hose, an NG quick-connect adapter, and a three-year limited warranty
Last update on 2025-04-17 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.