TIF-125 – Center Marker Light Missing – 2022 Tiffin Midas Motorhomes

SEOCONTENT-START

Page 1 of 3 Recall Inspection and Repair Instructions NHTSA Recall #: 22V-568 Tiffin Motorhomes Recall #: WAY-103 Models Involved: 2022 Midas Purpose: To provide instructions on how to relocate the back up camera and add a missing rear center marker light. Tools Needed: Parts Needed: Electric drill/impact driver w/Phillips head bit 2 of 015915, 16-14 AWG, Gel Filled, Butt Wire Connector High Speed Step Bit ¼” to 1 3/8” 3 ft of 001360 16 AWG Stranded Yellow Wire Wire Stripper/cutter 20-10 AWG 3 ft of 00135616 AWG Stranded White Wire Crimping & Cutting Tool 22 – 10 AWG 1 of 5064728, Light Marker Red Flat head screwdriver 1 of 5060967, Sealant, Clear, Exterior Royal 12781 10oz Digital Multimeter 1 of 2155, Heyco Flexible Shutter Bushing FLAT RATE CODE & TIME ALLOWED FOR VISUAL INSPECTION, EQUIPMENT RELOCATION, TERMINATION, AND SYSTEM CHECK: MD8808RC01 for up to 1.5 hours. Note for parts: Part numbers for the system components are listed above. Not all parts may be needed for repair. In addition, some shop supplies will be needed and should be billed back under the flat rate code for the recall. Note on systems: Below instructions represent proper procedures for repair, and testing. Images depict are shown for diagrammatical propose only and may not be reflective of each unit. INSPECTION PROCEDURE: 1. Turn chassis engine off and remove key from ignition switch. Place chassis light switch in off position. (Figure1) Figure: 1 Chassis Light Switch Page 2 of 3 REPAIR PROCEDURES: 1. Locate the rear backup camera mounted at the top rear of the back cap. The camera position will be between two of the rear marker lights center of coach. 2. Unplug rear camera from camera harness. 3. Remove screws from camera mounting bracket holding camera to back cap. 4. Once camera and bracket are removed there will be a center hole, locate the yellow and white marker light power wires and pull through the hole. There will be a yellow and white lead already for connection in the existing marker light harness. 5. Install a Qty. (1) part 5064728 – Light Marker Red (Figure 2) using gel filled butt wire connectors in the center between the other two existing marker lights. This light will cover the hole made from camera removal. Figure: Figure: 22 6. Seal around marker light, using a clear waterproof RTV silicone sealant. 7. Reinstalling the camera, using a step bit drill a 1.250” hole into rear cap. Position hole 4” from top as shown in (Figure 3), and 41 ½” from driver side as shown in (Figure 4) Figure: 4Figure: 4 Figure: Figure: 33 Drill 1.250” Hole Location Page 3 of 3 8. Install 1.250” bushing into hole and reposition the camera harness through bushing. See (Figure 5) FigurFigure: 5e: 5 9. Reinstall camera mounting bracket with / camera at position shown in Figure 5. 10. Plug camera harness back into camera see Figure 5. 11. Apply waterproof RTV Silicone Sealant to any screw heads, and open holes. 12. Final assembly arrangement will reflect setup shown in Figure 5. 13. Complete systems check as described below. A. Checking marker lights: Turn chassis ignition key switch to the on position. Then turn the chassis light switch on for the headlight position. Inspect that all marker lights are operational, and lamps are burning. B. Checking the backup camera: Start the chassis engine, with your foot on the brake place the unit into reverse. The radio display will show a rear camera image, verify the camera image for correct positioning. Adjust rear camera for correct image as needed.

**************************************************************************************************************

Page 1 of 3 Recall Inspection and Repair Instructions NHTSA Recall #: 22V-568 Tiffin Motorhomes Recall #: WAY-103 Models Involved: 2022 Midas Purpose: To provide instructions on how to relocate the back up camera and add a missing rear center marker light. Tools Needed: Parts Needed: Electric drill/impact driver w/Phillips head bit 2 of 015915, 16-14 AWG, Gel Filled, Butt Wire Connector High Speed Step Bit ¼” to 1 3/8” 3 ft of 001360 16 AWG Stranded Yellow Wire Wire Stripper/cutter 20-10 AWG 3 ft of 00135616 AWG Stranded White Wire Crimping & Cutting Tool 22 – 10 AWG 1 of 5064728, Light Marker Red Flat head screwdriver 1 of 5040576, Waterproof RTV Silicone Sealant Clear -75 to 500F Digital Multimeter 1 of 2155, Heyco Flexible Shutter Bushing FLAT RATE CODE & TIME ALLOWED FOR VISUAL INSPECTION, EQUIPMENT RELOCATION, TERMINATION, AND SYSTEM CHECK: MD8808RC01 for up to 1.5 hours. Note for parts: Part numbers for the system components are listed above. Not all parts may be needed for repair. In addition, some shop supplies will be needed and should be billed back under the flat rate code for the recall. Note on systems: Below instructions represent proper procedures for repair, and testing. Images depict are shown for diagrammatical propose only and may not be reflective of each unit. INSPECTION PROCEDURE: 1. Turn chassis engine off and remove key from ignition switch. Place chassis light switch in off position. (Figure1) Figure: 1 Chassis Light Switch Page 2 of 3 REPAIR PROCEDURES: 1. Locate the rear backup camera mounted at the top rear of the back cap. The camera position will be between two of the rear marker lights center of coach. 2. Unplug rear camera from camera harness. 3. Remove screws from camera mounting bracket holding camera to back cap. 4. Once camera and bracket are removed there will be a center hole, locate the yellow and white marker light power wires and pull through the hole. There will be a yellow and white lead already for connection in the existing marker light harness. 5. Install a Qty. (1) part 5064728 – Light Marker Red (Figure 2) using gel filled butt wire connectors in the center between the other two existing marker lights. This light will cover the hole made from camera removal. Figure: Figure: 22 6. Seal around marker light, using a clear waterproof RTV silicone sealant. 7. Reinstalling the camera, using a step bit drill a 1.250” hole into rear cap. Position hole 4” from top as shown in (Figure 3), and 41 ½” from driver side as shown in (Figure 4) Figure: 4Figure: 4 Figure: Figure: 33 Drill 1.250” Hole Location Page 3 of 3 8. Install 1.250” bushing into hole and reposition the camera harness through bushing. See (Figure 5) FigurFigure: 5e: 5 9. Reinstall camera mounting bracket with / camera at position shown in Figure 5. 10. Plug camera harness back into camera see Figure 5. 11. Apply waterproof RTV Silicone Sealant to any screw heads, and open holes. 12. Final assembly arrangement will reflect setup shown in Figure 5. 13. Complete systems check as described below. A. Checking marker lights: Turn chassis ignition key switch to the on position. Then turn the chassis light switch on for the headlight position. Inspect that all marker lights are operational, and lamps are burning. B. Checking the backup camera: Start the chassis engine, with your foot on the brake place the unit into reverse. The radio display will show a rear camera image, verify the camera image for correct positioning. Adjust rear camera for correct image as needed.

**************************************************************************************************************

Page 1 of 2 105 2nd Street NW Red Bay, Alabama 35582 IMPORTANT SAFETY RECALL This notice applies to your vehicle, VIN: NHTSA Recall # 22V-568 Tiffin Wayfarer Recall # WAY-103 August 19, 2022 Midas Center Marker Light Dear Tiffin Motorhome Owner or Dealer, This notice is sent to you in accordance with the requirements of the National Traffic and Motor Vehicle Safety Act. Tiffin Motorhomes has decided certain, 2022 Midas Motorhomes, fail to conform to Federal Motor Vehicle Safety Standard No. 108, “Lamps, reflective devices, and associated equipment”. Tiffin Motorhomes has become aware of the possibility that on these motorhomes, the rear center marker light was left off and the back up camera was put into the location for the rear center marker light. Not having the correct number of marker lights on the motorhome will impair the visibility of the motorhome to other drivers and may increase the risk of a crash. Tiffin Motorhomes will have the location of the rear back up camera relocated and have a rear center marker light installed in the correct location. Please arrange to take your motorhome to a reputable service center OR dealer of your choice to have the correction completed. A list of Tiffin Motorhomes authorized dealers is available online at https://tiffinmotorhomes.com/service-center-locations. The recall repair will take up to 1 hour and 30 minutes. If you are using a service center that is not a Tiffin Motorhomes authorized repair facility, please make sure that they contact Tiffin Motorhomes for the required parts, instructions and time allowed for the repair. Tiffin Motorhomes will not pay over the allowed time unless the repair facility receives a prior authorization. For authorization, contact Tiffin Motorhomes at 256-356-0261 or [email protected] . You may be liable for any progressive damage that results from your failure to complete the recall within a reasonable time after receiving notification. If owners have paid to have this repair completed, please send a copy of the invoice, that was paid by the owner to Tiffin Motorhomes at the following address: Tiffin Motorhomes, attn: Recalls, 105 2nd Page 2 of 2 Street NW, Red Bay AL 35582 or by email to [email protected]. Please make sure the invoice notes who paid for the repair, the VIN of the motorhome and the date the repair was completed. If you do not own the vehicle that corresponds to the vehicle identification number which appears on this Recall Notification, please return the notification to the Tiffin Warranty Department with any information you can furnish that will assist us in locating the present owner. You may also send an email to [email protected]. If you are unable to have the defect remedied without charge and within a reasonable time after you tender the vehicle for repair, please contact the Tiffin Warranty Department, at 1-256-356-8661, 8:00 a.m. to 3:30 p.m., Central Time. For US Customers: You may also wish to notify the Administrator, National Highway Traffic Safety Administration, 1200 New Jersey Avenue SE, Washington DC 20590, or phone 1-888-327-4236 (TTY: 1-800-424-9153): or go to http://www.safercar.gov. Federal regulations require that any vehicle lessor receiving this recall notice must forward a copy of this notice to the lessee within ten days. We regret any inconvenience this action may cause but feel certain you understand our interest in motor vehicle safety. Tiffin Recall Department

**************************************************************************************************************

105 2nd Street NW Red Bay, Alabama 35582 IMPORTANT SAFETY RECALL NHTSA Recall # 22V-568 Tiffin Wayfarer Recall # WAY-103 August 15, 2022 Midas Rear Center Marker Light Dear Tiffin Motorhome Dealer, This notice is sent to you in accordance with the requirements of the National Traffic and Motor Vehicle Safety Act. Tiffin Motorhomes has decided certain, 2022 Midas Motorhomes, fail to conform to Federal Motor Vehicle Safety Standard No. 108, “Lamps, reflective devices, and associated equipment”. Tiffin Motorhomes has become aware of the possibility that on these motorhomes, the rear center marker light was left off and the backup camera was put into the location for the rear center marker light. Not having the correct number of marker lights on the motorhome will impair the visibility of the motorhome to other drivers and may increase the risk of a crash. Tiffin Motorhomes will have the location of the rear back up camera relocated and have a rear center marker light installed in the correct location. Owners will be notified by mail about the recall and will be instructed to take their motorhome to a reputable service center OR dealer of their choice to have this repair completed. Tiffin Motorhomes is allowing 1 hour and 30 minutes for the repair to be completed. To verify a motorhome’s involvement in this recall, please visit our website, TiffinMotorhomes.com. Choose the “Dealer Login” page and click on “Vehicle Recall Lookup” and enter the complete 17-digit VIN number. No login or password is needed. To view work instructions, please click on “Flat Rate Manual” and choose “Recalls” for Model and “Wayfarer Recalls” for Section, scroll down to the NHTSA recall number for the recall you are looking for and choose “Show Files” and then download the work instructions. Please be reminded that it is a violation of Federal law for you to sell or lease any new Tiffin Motorhome covered by this notification until this recall has been performed on the motorhome. Substantial civil penalties apply to violations of this law. We regret any inconvenience this action may cause but feel certain you understand our interest in motor vehicle safety. Tiffin Compliance Department

**************************************************************************************************************

OMB Control No.: 2127-0004 Part 573 Safety Recall Report 22V-568 The information contained in this report was submitted pursuant to 49 CFR §573 Manufacturer Name : Tiffin Motorhomes, Inc. Submission Date : AUG 10, 2022 NHTSA Recall No. : 22V-568 Manufacturer Recall No. : TIF-125 Manufacturer Information : Manufacturer Name : Tiffin Motorhomes, Inc. Address : 105 2nd Street NW PO Box 596 Red Bay AL 35582 Company phone : 999 Population : Number of potentially involved : 10 Estimated percentage with defect : 100 % Vehicle Information : Vehicle 1 : 2022-2022 Tiffin Midas Vehicle Type : BUSES, MEDIUM & HEAVY VEHICLES Body Style : OTHER Power Train : GAS Descriptive Information : Center marker light left off on all units produced since the beginning of Midas production. Production Dates : DEC 21, 2021 – JUL 27, 2022 VIN Range 1 : Begin : NR End : NR Not sequential Description of Noncompliance : Description of the Noncompliance : Center marker light left off due to back-up camera was put in it’s place in the rear cap. FMVSS 1 : 108 – Lamps, reflective devices, and assoc. Equipment FMVSS 2 : NR Description of the Safety Risk : It is a marker light used for others to see coach. If not there, the visibility of coach to others could be impaired and cause increase risk of crash. Description of the Cause : The hole in the rear cap that was supposed to house the center marker light was used instead for back-up camera. Error in production. Identification of Any Warning that can Occur : None. Involved Components : Part 573 Safety Recall Report 22V-568 Page 2 The information contained in this report was submitted pursuant to 49 CFR §573 Component Name 1 : Marker Light Component Description : Center Marker Light Component Part Number : 5127680 (Tiffin part #) Supplier Identification : Component Manufacturer Name : NR Address : NR NR Country : NR Chronology : 7/27/22 Safety Committee was advised of non-compliance due to center marker light had been left off. Decision was made to submit 573 for recall. No vote needed. There have been no claims or reports of problems to date. Description of Remedy : Description of Remedy Program : Tiffin will notify the affected population and have the camera moved down and center marker light inserted. This install will be at no charge to owner. If the owner has paid for any repairs related to this defect, they can submit their invoice to Tiffin Motorhomes for reimbursement. How Remedy Component Differs from Recalled Component : The remedied unit will have the center marker light, whereas the recalled unit will not. Identify How/When Recall Condition was Corrected in Production : Engineering Change Modification dated 7/28/2022 states “Move camera down and add center marker light”. Recall Schedule : Description of Recall Schedule : Owners and dealers will be notified of the recall and the Installation of the center marker light will be performed at no charge to the customer. Planned Dealer Notification Date : SEP 30, 2022 – SEP 30, 2022 Planned Owner Notification Date : SEP 30, 2022 – SEP 30, 2022 Part 573 Safety Recall Report 22V-568 Page 3 The information contained in this report was submitted pursuant to 49 CFR §573 * NR – Not Reported

**************************************************************************************************************

OMB Control No.: 2127-0004 Part 573 Safety Recall Report 22V-568 The information contained in this report was submitted pursuant to 49 CFR §573 Manufacturer Name : Tiffin Motorhomes, Inc. Submission Date : AUG 18, 2022 NHTSA Recall No. : 22V-568 Manufacturer Recall No. : WAY-103 Manufacturer Information : Manufacturer Name : Tiffin Motorhomes, Inc. Address : 105 2nd Street NW PO Box 596 Red Bay AL 35582 Company phone : 999 Population : Number of potentially involved : 10 Estimated percentage with defect : 100 % Vehicle Information : Vehicle 1 : 2022-2022 Tiffin Midas Vehicle Type : BUSES, MEDIUM & HEAVY VEHICLES Body Style : OTHER Power Train : GAS Descriptive Information : Center marker light left off on all units produced since the beginning of Midas production. Production Dates : DEC 21, 2021 – JUL 27, 2022 VIN Range 1 : Begin : NR End : NR Not sequential Description of Noncompliance : Description of the Noncompliance : Center marker light left off due to back-up camera was put in it’s place in the rear cap. FMVSS 1 : 108 – Lamps, reflective devices, and assoc. Equipment FMVSS 2 : NR Description of the Safety Risk : It is a marker light used for others to see coach. If not there, the visibility of coach to others could be impaired and cause increase risk of crash. Description of the Cause : The hole in the rear cap that was supposed to house the center marker light was used instead for back-up camera. Error in production. Identification of Any Warning that can Occur : None. Involved Components : Part 573 Safety Recall Report 22V-568 Page 2 The information contained in this report was submitted pursuant to 49 CFR §573 Component Name 1 : Marker Light Component Description : Center Marker Light Component Part Number : 5127680 (Tiffin part #) Supplier Identification : Component Manufacturer Name : NR Address : NR NR Country : NR Chronology : 7/27/22 Safety Committee was advised of non-compliance due to center marker light had been left off. Decision was made to submit 573 for recall. No vote needed. There have been no claims or reports of problems to date. Description of Remedy : Description of Remedy Program : Tiffin will notify the affected population and have the camera moved down and center marker light inserted. This install will be at no charge to owner. If the owner has paid for any repairs related to this defect, they can submit their invoice to Tiffin Motorhomes for reimbursement. How Remedy Component Differs from Recalled Component : The remedied unit will have the center marker light, whereas the recalled unit will not. Identify How/When Recall Condition was Corrected in Production : Engineering Change Modification dated 7/28/2022 states “Move camera down and add center marker light”. Recall Schedule : Description of Recall Schedule : Owners and dealers will be notified of the recall and the Installation of the center marker light will be performed at no charge to the customer. Planned Dealer Notification Date : SEP 30, 2022 – SEP 30, 2022 Planned Owner Notification Date : SEP 30, 2022 – SEP 30, 2022 Part 573 Safety Recall Report 22V-568 Page 3 The information contained in this report was submitted pursuant to 49 CFR §573 * NR – Not Reported

**************************************************************************************************************

OMB Control No.: 2127-0004 Part 573 Safety Recall Report 22V-568 The information contained in this report was submitted pursuant to 49 CFR §573 Manufacturer Name : Tiffin Motorhomes, Inc. Submission Date : AUG 03, 2022 NHTSA Recall No. : 22V-568 Manufacturer Recall No. : TIF-125 Manufacturer Information : Manufacturer Name : Tiffin Motorhomes, Inc. Address : 105 2nd Street NW PO Box 596 Red Bay AL 35582 Company phone : 999 Population : Number of potentially involved : 10 Estimated percentage with defect : 100 % Vehicle Information : Vehicle 1 : 2022-2022 Tiffin Midas Vehicle Type : BUSES, MEDIUM & HEAVY VEHICLES Body Style : OTHER Power Train : GAS Descriptive Information : Center marker light left off on all units produced since the beginning of Midas production. Production Dates : DEC 21, 2021 – JUL 27, 2022 VIN Range 1 : Begin : NR End : NR Not sequential Description of Noncompliance : Description of the Noncompliance : Center marker light left off due to back-up camera was put in it’s place in the rear cap. FMVSS 1 : 108 – Lamps, reflective devices, and assoc. Equipment FMVSS 2 : NR Description of the Safety Risk : It is a marker light used for others to see coach. If not there, the visibility of coach to others could be impaired. Description of the Cause : The hole in the rear cap that was supposed to house the center marker light was used instead for back-up camera. Error in production. Identification of Any Warning that can Occur : None. Involved Components : Part 573 Safety Recall Report 22V-568 Page 2 The information contained in this report was submitted pursuant to 49 CFR §573 Component Name 1 : Marker Light Component Description : Center Marker Light Component Part Number : 5127680 (Tiffin part #) Supplier Identification : Component Manufacturer Name : NR Address : NR NR Country : NR Chronology : 7/27/22 Safety Committee was advised of non-compliance due to center marker light had been left off. Decision was made to submit 573 for recall. No vote needed. Description of Remedy : Description of Remedy Program : Tiffin will notify the affected population and have the camera moved down and center marker light inserted. This install will be at no charge to owner. If the owner has paid for any repairs related to this defect, they can submit their invoice to Tiffin Motorhomes for reimbursement. How Remedy Component Differs from Recalled Component : The remedied unit will have the center marker light, whereas the recalled unit will not. Identify How/When Recall Condition was Corrected in Production : Engineering Change Modification dated 7/28/2022 states “Move camera down and add center marker light”. Recall Schedule : Description of Recall Schedule : Owners and dealers will be notified of the recall and the Installation of the center marker light will be performed at no charge to the customer. Planned Dealer Notification Date : SEP 30, 2022 – SEP 30, 2022 Planned Owner Notification Date : SEP 30, 2022 – SEP 30, 2022 * NR – Not Reported

SEOCONTENT-END