โThis site contains affiliate links for which OEMDTC may be compensatedโ |
April 5, 2023 NHTSA CAMPAIGN NUMBER: 23V240000
Loaded Bike Rack Obstructs Rear Lighting/FMVSS 108
Obstructed rear lighting may reduce the visibility of the vehicle to other drivers, increasing the risk of a crash.
NHTSA Campaign Number: 23V240
Manufacturer Motor Coach Industries
Components EQUIPMENT
Potential Number of Units Affected 140
Summary
Motor Coach Industries (MCI
) is recalling certain 2019-2021 D45CRTLE, J3500, and J4500 coaches, equipped with a rear-mounted bike rack. The vehicle’s rear lighting may be obstructed when bikes are installed on the bike rack. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 108, “Lamps, Reflective Devices, and Associated Equipment.”
Remedy
MCI will provide instructions and a kit to add lighting to the rear-mounted bike rack, free of charge. Owner notification letters were mailed August 31, 2023. Owners may contact MCI
customer service at 1-800-241-2947.
Notes
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.nhtsa.gov.
ITS: 60725
ISSUE:
When bicycles are loaded onto the rear bike racks, can block the brake, and tell lights.
SUMMARY:
Install auxiliary rear brake and tell lights.
Chronology :
-Late 2022, MCI receives a request from a customer to install a 5-position bike rack on the rear of the coach
-February 2023, as design releases occur, it was noted there was a missing validation report for FMVSS 108 with the bike rack installed.
-Early-March 2023 MCI arranges for an outside test facility to check lighting with the rack installed to FMVSS 108.
-Mid-March 2023 โ testing indicated likely non-compliance when bikes are mounted on the rack, where the inward angle lighting was impacted, in noncompliance with 108 6.1.3 Mounting location, —6.1.3.1, โโฆcomplies with all photometric requirementsโฆwith all obstructions considered.โ
-March 24, 2023 โ analysis continues on the lighting angle candela readings via coach CAD models
-March 27, 2023 โ engineering determined the bikes, as mounted, are deemed โobstructionsโ and would affect the inboard angle requirements.
-March 31, 2023 โ issue was raised to the Vehicle Safety Committee where a recall determination was made
9 Affected Products
Vehicles
9 Associated Documents
Noncompliance Notice 573 Report
RCLRPT-23V240-6874.PDF 215.492KB
Recall Acknowledgement
RCAK-23V240-5652.pdf 737.225KB
ISSUED Interim Owner Notification Letter(Part 577)
RCONL-23V240-5100.pdf 145.21KB
Part 577 Owner Notification Envelope
Remedy Instructions and TSB
RCRIT-23V240-0467.pdf 634.299KB
ISSUED Owner Notification Letter(Part 577)
RCONL-23V240-2270.pdf 138.627KB
Recall Quarterly Report #1, 2023-3
RCLQRT-23V240-6454.PDF 211.275KB
Recall Quarterly Report #2, 2023-4
RCLQRT-23V240-3340.PDF 211.376KB
Recall Quarterly Report #3, 2024-1
RCLQRT-23V240-2498.PDF 211.453KB
Latest Recalls Documents
- ENERGY EFFICIENT & Multifunction Camper
Light: Low-profile RV tail light serves 4 function as stop light, turn signal light, taillight. Using advanced LED combination light with better heat distribution, brighter and more energy-efficient than halogen bulbs. This RV camper
light Left hand driver's side: 29 Diodes( 24 Red++5 White ); Right Hand Passenger's Side: 24 Diodes; this light uses LEDs.
- Durable white plastic base with acrylic RED lens, provide better light with less power output bring reliable visibility and safety even in inclement weather.
- WATERPROOF: Waterproof rate IP67, effectively protects the rv tail light from dust, sand, moisture, rain and other impact of inclement weather. Each lens is sonically welded to the housing and built to ensure maximum durability in working conditions for your vehicles.
- Easy Installation: Directly mounts on surface of trailer - hardware not included. RV light set come with 3 specific colored wires for easy connection. White wire: Negative(Ground). White + Black Wire: Tail Lights; White + Red Wire: Brake/Turn Signal Lights.
- Widely Application: Ideal for most 12V vehicles including Trailers, Tractors, Semi-Trailer, Dump Truck, Pickup, Camper
, UTEs, UTVs, Boat, Caravans, flatbed, special vehicle etc.
- [Multi-Functional Tail Light] Serves as a stop light, turn signal light, taillight, and backup light; equipped with white LEDs in the center for added brightness; ideal for trailers, RVs, motorhomes, or upgrades for other vehicles
- [Surface Mount Design] Features a surface mount installation with screws included; can be mounted horizontally or vertically; includes built-in reflector strips and a mounting gasket for a tight seal and cushioning
- [Hardwired Connection] Includes 6 wires for easy installation; white for ground, blue for backup/reverse, green and yellow for stop or turn signals, black and brown for tail or running lights
- [Slim Profile Dimensions] Measures approximately 14 inches in length, 6 7/8 inches in width, and 1/2 inch in thickness; wire knob area measures 1 inch thick and 1 3/16 inches in diameter, requiring a cutout for proper fit
- [Complete Package] Comes with 2 rectangular rv trailer lights; includes screws and foam gaskets for a secure and cushioned installation
- Combination stop/turn/tail light for surface mounting. Equipped with a single L.E.D. diode that varies its' brightness depending upon what function is being utilized. DOT approved for trailers over 80 inches wide. Package contains (1) left side and (1) right side.
- 3-3/16" height x 8-11/16" width x 2-1/4" depth. Hard wire style of connection. 12V DC .34 amps.
- 1-7/8" x 7-3/8" mounting pattern. Acrylic lens and plastic housing
- Hard wired, includes separate ground wire. Black base
- Please note - mounting screws are not included.
- Unique US Flag Design:Rv trailer lights come with four functions,which are running light/turn signal light/Brake light/license plate light.Built with US Flag design,upgraded your RV Camper
or Trailer a unique and stylish look on the road.IP67 waterproof,the lens and the rear shell are tightly connected with waterproof silicone,50000 hrs life span, could work at all conditions.Upgrade cooling system,maintain 65 โ after lighting tested over two hours at maximum power.
- High Performance LEDs:Used High intensive 57 PCS LEDs in total,each led camper
tail light employs 24PCS quality red led chips,one of the led rv tail light built with license plate holder and 9PCS high brightness white leds for license plate,others only have 5PCS leds for license plate! Outputs amazing bright and stable RV Tail light. Features better visibility and safety, also add a bonus of charming light for your night trip.
- Easy Installation:Rv camper
tail lights designed with 3 specific colored wires for easy connection.Black wire is negative,Red wire is brake light and turn signal light, and Yellow wire is running light.The license plate light will be also light up,when the running light is on.Come with instructions,and this rv tail lights have mounting holes,which can be installed close to surface of the trailer,usually can be installed within 20 minutes.
- Widely Application: Travel rv tail light kit fits for most 12V vehicles including Camper
, Trailers, semi-trailer, Tractors, Dump trucks, Caravans, UTVs, Pickup, flatbed, UTEs, Boat, special vehicles etc.
- Package Included: 2PCSx rv led tail lights+ 1 Set of screws+1PCS of installation instruction.
- Excellent brightness: The driver side light contains 30pcs LEDs (24pcs for red light and 6pcs for license plate light), and the passenger side light contains 24pcs LEDs for red light. Bright light makes it easy for vehicles behind to distinguish changes of the lights, making driving safer
- Surface Mount: Equipped with necessary screws for installation, with a screw length of 20mm. By using the surface mount method, after finding a suitable installation location, reserve the hole position for the wire in advance, and then fix the lights to the vehicles with screws. Finally, connect the wires
- Wiring & Functions: Included three colors wires. White is for Ground, black wires for low brightness running light and license plate light, and red wires for high brightness brake stop turn signals light
- Premium Materials & Waterproof: The combination of high-quality PC lens and ABS
bottom shell effectively protects the internal LED and circuit board, while enhancing waterproof performance. Let the tail light work normally in rainstorm or other bad weather
- Wide Application: Fit for 12V DC trailers, RVs, Camper
, Vans etc. Function as running/stop brake/turn signal/back up reverse/tail light
- Description: Combination stop/turn/tail light with white base. 4.3 Lumens
- Features: Snap-on, replaceable lens and easy to change bulbs
- Durability: All weather molded plastic housing and durable lens build resists corrosion
- Included: Ground wire included
- Usage: These tail lights feature superior design and replacement flexibility
- [Multi-Function Light Kit] 8 5/8" x 3 7/8" rectangle trailer tail light kit performs 3 functions - stop light, turn signal light, and taillight; includes a built-in license plate light and mounting brackets on the left-hand driver's side
- [49 LEDs] Features 27 diodes on the left-hand side (22 red + 5 white) and 22 diodes on the right-hand side; LEDs last up to 50 times longer than incandescent bulbs, use less power, and eliminate the need for bulb replacements
- [Easy Wiring] Includes 3 pre-attached wiresโwhite for ground, black for taillight, and red for brake and turn signal; complies with SAE and DOT standards for safety
- [Dimensions] Measures 8 5/8" in length, 3 7/8" in height, and 1 3/5" in depth; mounting holes are spaced approximately 7" by 2 1/2" apart for secure installation
- [Surface-Mount Design] Installs flat on trailers or campers
using a flange or bracket with pre-drilled mounting holes; no need to cut into the surface for installation
- PATRIOTIC FLAIR ON THE GO- Flaunt your American pride with our unique 57 LED RV Tail Lights, boasting an eye-catching US flag design. Illuminate your camper
or trailer with a touch of patriotism while ensuring high visibility and safety on the road.
- SUPERIOR LIGHTING PERFORMANCE- Outshine the competition with our high-performance tail lights, featuring 57 powerful LEDs. Our tailored design includes an integrated license plate holder enhanced with 9 ultra-bright white LEDs, ensuring your plate is clearly visible, a step above others with only 5 LEDs.
- EFFORTLESS SETUP- Installation is a breeze with our user-friendly, color-coded wiring system โ black for ground, red for brake/turn signals, and yellow for running lights. Each set includes easy-to-follow instructions and pre-drilled mounting holes to get you back on the road in no time.
- VERSATILE COMPATIBILITY- Our tail lights are the perfect fit for a wide array of 12V vehicles. Whether you're driving a camper
, trailer, semi-trailer, tractor, caravan, UTV, pickup, flatbed truck, boat, or other special vehicles, our lights provide the upgrade you need for a safe and stylish journey.
- COMPLETE TAIL LIGHT KIT- Each package delivers everything you need for a full upgrade โ 2 RV LED Tail Lights, a complete set of screws for secure attachment, and clear installation instructions. Plus, enjoy peace of mind with our 12-month warranty and dedicated customer service team.
- ใMulti-Functionใ: The RV tail lights with turn signal light, brake light and tail light 3 functions, and when the tail light is on, the license plate light will also be on. Rv trailer lights using advanced LED combination lights, The lens has good light transmittance, brighter and energy-saving
- ใApplicable Modelsใ: This camper
tail lights are suitable for most 12V vehicles including Camper
, Trailers, semi-trailer, Tractors, Dump trucks, Caravans, UTVs, Pickup, flatbed, UTEs, Boat, special vehicles etc. Some RV original tail lights may not match the size of ours, so please check your size before purchasing
- ใGood Materialใ:The shell of the rv brake lights are made of plastic, the lens and the rear shell are tightly connected with waterproof silicone, which can effectively waterproof, dust-proof, and anti-corrosion, which greatly extends the service life, and can work safely even in bad weather
- ใEasy Installationใ: There are three different color wires on the back of this rv led tail lights. The white wire is ground, the red wire is brake light, and the black wire is running light, which is convenient to connect. This rv trailer tail lights have mounting holes, which can be installed close to the surface of the trailer, which greatly saves your precious time
- ใPackage Contentsใ: 1 x Left side led camper
tail light + 1 x Right side led camper
tail light + a pack of screws. One year product support, if you have any product-related problems, we're here to assist you
- [Package Contents] Includes 2 LED triple horizontal mount taillights with a black base; features 8 screw holes for secure mounting; stainless steel screws and mounting gaskets included for a tight seal
- [Light Configuration] Features 3 red lenses; includes 2 replaceable red LED stop, tail, and turn lights; 1 clear backup light with a red reflex lens border and built-in white LEDs
- [Versatile Mounting Options] Can be mounted horizontally or vertically; suitable for surface or flat mounting to fit various applications
- [Wiring Specifications] Hardwired with 8 wires; includes white for ground, blue for backup/reverse light, red for high mode (stop/turn signals), and black for low mode (tail/running lights); may require resistors for halogen to LED upgrades
- [Dimensions] Overall length of approximately 14.17 inches, width of about 7 inches, and thickness of 0.87 inch; requires a cutout of 13.4 inches long by 6.3 inches hole to hole for installation
SEOCONTENT-START
THIS ITS DOCUMENT SHOULD BE RETAINED AND REFERRED TO FOR FUTURE MAINTENANCE UNTIL
THE NEW FLYER PARTS AND/OR SERVICE MANUAL IS UPDATED TO REFLECT WORK DONE AS A
RESULT OF THIS DOCUMENT. ENSURE THAT THIS DOCUMENT IS AVAILABLE FOR PARTS AND
MAINTENANCE STAFF GOING FORWARD.
This document and the contents discussed herein are the confidential and proprietary information of New Flyer Industries Canada
ULC and New Flyer of America Inc. and are disclosed by New Flyer
in confidence. This document and the contents herein are not
to be disclosed by the intended recipient without the prior written authorization of New Flyer. Any unauthorized disclosure,
reproduction or other distribution of this document or information strictly prohibited and may result in action being taken against
the party making the unauthorized disclosure. This document and all copies hereof must be returned to New Flyer upon request.
INSTRUCTION TO SERVICE
ITS: 60725
SECTION:
273 โ Exterior Lights.
WRITTEN BY:
Scott Geier Technical Service Specialist.
ISSUE:
When bicycles are loaded onto the rear bike racks, can block the brake, and tell lights.
SUMMARY:
Install auxiliary rear brake and tell lights.
ITS- 60725
Ref. NHTSA Recall No.
Ref. Transport Canada Recall No.
23V240
Not Applicable
INSTRUCTION TO SERVICE
ITS- 60725 Page 2 of 8
INSTRUCTION TO SERVICE
ITS- 60725 Page 3 of 8
PROCEDURE:
1. Turn the main battery disconnect switch to the โOFFโ position.
2. Using light plates (Item # 1), and (Item #2), as a templates, drill ยผ inch dia. hole through the face of the bike rack frame tube. Ensure only first of the tube is drilled through. Secure plates to the frame using rivets (Item #5). See figure 1 for light bracket installation measurements.
Figure 1: Light brackets installation reference.
3. Install lights (Item #3) with grommets (Item #4) into the light plates. See figure 2.
Figure 2: Lights and grommets installaton reference.
INSTRUCTION TO SERVICE
ITS- 60725 Page 4 of 8
4. Route auxiliary lights rear bike harness (Item #7) from the streetside taillights to the curbside taillights along the existing engine compartment harnesses. See figure 3.
Figure 3: Auxiliary lights rear bike harness installation reference.
INSTRUCTION TO SERVICE
ITS- 60725 Page 5 of 8
5. From the auxiliary lights rear bike harness (Item #7), connect EC-P539, EC-P540, EC-P542, EC-P543 to engine compartment harness. Then connect EC-P539A, EC-P540A, EC-P542A, EC-P543A to the turn, tail, and stop lights. See figures 4.
Figure 4: Auxiliary lights rear bike harness streetside and curbside bus harness reference.
INSTRUCTION TO SERVICE
ITS- 60725 Page 6 of 8
6. Route auxiliary lights rear bike harness (Item #7) through the hole in the rear bumper, along the bike rack frame as shown in view โFโ, section D-D, detail โHโ, and section G-G.
7. Drill 17/64-inch dia. hole onto the right-side bottom tube assembly bracket and bumper beam. Mount bracket using clamps (Item #9) as a guide and as per section G-G. Secure auxiliary lights bike rack harness (Item #7) in place using clamps and secure using tapping screws (Item #10).
8. Drill 17/64-inch dia. hole onto the rear bike frame using clamps (Item #9) as a guide and as per section D-D, detail โEโ. Secure harness using self-tapping screws (Item #10).
INSTRUCTION TO SERVICE
ITS- 60725 Page 7 of 8
9. Install connectors to the rear auxiliary lights on the bike rack. See figure 5.
Figure 5: Auxiliary lights rear bike harness connection to aux bike lights reference.
10. Install adhesive tie base onto interior side of the curbside bumper and fasten harness using tyraps (Item #11).
NOTE: Clean surface where tie base will be applied with isopropyl alcohol (Item #12 NF PN: 23-05-0005) and allow 60 seconds of flash-off before applying tie base.
11. Use tyraps (Item #11) as required to secure the harnesses. Coil up any extra length in the engine compartment.
12. Apply Sikaflex (Item #12) as required to seal holes in the rear bumper.
13. Turn the main battery disconnect switch to the โONโ position.
14. Start the bus and perform brake, turn, and tell light function test.
INSTRUCTION TO SERVICE
ITS- 60725 Page 8 of 8
LABOUR ESTIMATE
Operation
Number of Technician(s)
Hours
Labor Time
T X HR
1
Install auxiliary rear brake and tell lights.
1
1.50
1.50
PARTS REQUIRED
Item
Part Number
Description
Qty.
per Coach
Units
Notes
1
1023667
PLATE-LIGHT L/R
2
EA
2
1023712
PLATE-LIGHT CENTER
1
EA
3
07-07-1932
LAMP – TAIL LIGHT, LED
6
EA
4
07-07-1941
GROMMET
6
EA
5
336379
RIVET-HUCKLOK 1/4″ .187-.437
12
EA
7
1024592
HRNS-AUX LTS REAR BIKE RACK
1
EA
8
19-04-0283
TIE BASE – ADH MT
1
EA
9
19-04-0451
CLAMP-LINE SUPPORT 9/16″I.D, SILICONE COVERED, ORA
5
EA
10
19-1-529
SCREW-TAPPING,THREAD ROLLING,DOG POINT
5
EA
11
19-11-258
TYRAP-7.31″ LONG,BLACK
26
EA
12
23-02-0016
SIKAFLEX – UV BLACK
0.010
OZ
13
23-05-0005
ALCOHOL – ISOPROPYL
0.010
OZ
**************************************************************************************************************
IMPORTANT SAFETY RECALL NOTICE
18-May-2023 VIA EMAIL AND US MAIL
Loop Trans, Inc.
615 Dado ST
San Jose, CA 95131
Subject: Motor Vehicle Safety Recall 23V240 โ rear lighting with bicycle rack (loaded)
To Whom it May Concern:
This notice is sent to you in accordance with the requirements of the National Traffic and Motor Vehicle Safety Act. Motor Coach Industries, Inc. (MCI) has decided that 2019-2021 MCI Model D45CRTLE, J3500 and J4500 coaches equipped with an optional rear mounted bicycle rack, MCI PN NS03-33-3736 or 951488 fail to conform to Federal Motor Vehicle Safety Standard No. 108; Lamps, reflective devices, and associated equipment. MCI has determined Loop Trans, Inc. is the Owner/Operator of the vehicles listed below which are affected by this recall action.
Make: MCI
Model Year VIN Model Year VIN
J 3500
2021
2MGKJMXAXMW021064
J 3500
2021
2MGKJMXA9MW021069
J 3500
2021
2MGKJMXA1MW021065
J 3500
2021
2MGKJMXA5MW021070
J 3500
2021
2MGKJMXA3MW021066
J 3500
2021
2MGKJMXA7MW021071
J 3500
2021
2MGKJMXA5MW021067
J 3500
2021
2MGKJMXA9MW021072
J 3500
2021
2MGKJMXA7MW021068
J 3500
2021
2MGKJMXA0MW021073
When bicycles are loaded onto the rack, the bicycles can obscure or reduce the lighting displayed rearward to traffic behind the coach.
Obscured lighting increases the risk of a crash.
An auxiliary lighting kit and labor required to accomplish the recall will be provided by MCI free of charge. MCI will install the lighting kit and ensure proper functionality. Please contact your TSM, RPSM or the MCI Customer Service Line at 1-800-241-2947 and arrange for the corrective action to be incorporated on your coach at your nearest MCI Service Center.
Alternatively, you can request parts and instructions necessary to conduct this retrofit and charge the time for actual labor back to MCI through the normal warranty process. MCI estimates the repair time to be approximately 4 hours, excluding vehicle and shop logistics.
The necessary parts and instructions required to conduct this corrective action are planned to be available in July 2023.
Until the corrective action can be incorporated on the above vehicles, MCI recommends against utilizing the bicycle rack.
Page 2 of 2
If you are a lessor of vehicles which are affected, it is required that any vehicle lessor receiving this recall notice must forward a copy of this notice to the lessee within ten days.
If you have sold or otherwise transferred the vehicle(s) identified above, please contact the MCI Customer Service Line at 1-800-241-2947 with all of the information you have regarding the current owner/operator of the vehicle(s).
If you had this corrective action performed before you received this letter, you may be eligible to receive reimbursement for the cost of obtaining a pre-notification remedy of the problem associated with this recall. Please contact your TSM (Technical Service Manager) or RPSM (Regional Product Support Manager) with details.
If MCI is unable to correct this defect within a reasonable time, you may submit a written complaint to the:
Administrator,
National Highway Traffic Safety Administration, 1200 New Jersey Ave. SE,
Washington, DC, 20590,
Or call 1-888-327-4236 (TTY: 1-800-424-9153);
or go to http://www.safercar.gov.
We regret any inconvenience which this action may cause you. However, we are concerned about the safety of your passengers and employees.
Thank you for your attention to this important matter.
Sincerely,
MOTOR COACH INDUSTRIES INC.
By: Jim Johnson
Vehicle Safety & Regulatory Compliance Manager
(256) 453-7181
Jim_johnson@newflyer.com
**************************************************************************************************************
IMPORTANT SAFETY RECALL NOTICE
DATE VIA FIRST CLASS US MAIL
Loop Trans, Inc.
615 Dado ST
San Jose, CA 95131
Subject: Motor Vehicle Safety Recall 23V240 โ rear lighting with bicycle rack (loaded)
To Whom it May Concern:
This notice is sent to you in accordance with the requirements of the National Traffic and Motor Vehicle Safety Act. Motor Coach Industries, Inc. (MCI) has decided that 2019-2021 MCI Model D45CRTLE, J3500 and J4500 coaches equipped with an optional rear mounted bicycle rack, MCI PN NS03-33-3736 or 951488 fail to conform to Federal Motor Vehicle Safety Standard No. 108; Lamps, reflective devices, and associated equipment. MCI has determined Loop Trans, Inc. is the Owner/Operator of the vehicles listed below which are affected by this recall action.
Make: MCI
Model Year VIN Model Year VIN
J 3500
2021
2MGKJMXAXMW021064
J 3500
2021
2MGKJMXA9MW021069
J 3500
2021
2MGKJMXA1MW021065
J 3500
2021
2MGKJMXA5MW021070
J 3500
2021
2MGKJMXA3MW021066
J 3500
2021
2MGKJMXA7MW021071
J 3500
2021
2MGKJMXA5MW021067
J 3500
2021
2MGKJMXA9MW021072
J 3500
2021
2MGKJMXA7MW021068
J 3500
2021
2MGKJMXA0MW021073
When bicycles are loaded onto the rack, the bicycles can obscure or reduce the lighting displayed rearward to traffic behind the coach.
Obscured lighting increases the risk of a crash.
We are pleased to inform you the lighting kits are now available. We urge you to contact your TSM, RPSM or the MCI Customer Service Line at 1-800-241-2947 and arrange for the corrective action to be incorporated on your coach at your nearest MCI Service Center.
This auxiliary lighting kit and labor required to accomplish the recall will be provided by MCI free of charge. MCI will install the lighting kit and ensure proper functionality.
Alternatively, you can request parts and instructions necessary to conduct this retrofit and charge the time for actual labor back to MCI through the normal warranty process. MCI estimates the repair time to be approximately 1.5 hours, excluding vehicle and shop logistics.
Page 2 of 2
If you are a lessor of vehicles which are affected, it is required that any vehicle lessor receiving this recall notice must forward a copy of this notice to the lessee within ten days.
If you have sold or otherwise transferred the vehicle(s) identified above, please contact the MCI Customer Service Line at 1-800-241-2947 with all of the information you have regarding the current owner/operator of the vehicle(s).
If you had this corrective action performed before you received this letter, you may be eligible to receive reimbursement for the cost of obtaining a pre-notification remedy of the problem associated with this recall. Please contact your TSM (Technical Service Manager) or RPSM (Regional Product Support Manager) with details.
If MCI is unable to correct this defect within a reasonable time, you may submit a written complaint to the:
Administrator,
National Highway Traffic Safety Administration, 1200 New Jersey Ave. SE,
Washington, DC, 20590,
Or call 1-888-327-4236 (TTY: 1-800-424-9153);
or go to http://www.safercar.gov.
We regret any inconvenience which this action may cause you. However, we are concerned about the safety of your passengers and employees.
Thank you for your attention to this important matter.
Sincerely,
MOTOR COACH INDUSTRIES INC.
By: Jim Johnson
Vehicle Safety & Regulatory Compliance Manager
(256) 453-7181
Jim_johnson@newflyer.com
**************************************************************************************************************
OMB Control No.: 2127-0004
Part 573 Safety Recall Report 23V-240
The information contained in this report was submitted pursuant to 49 CFR ยง573
Manufacturer Name : Submission Date :
Motor Coach Industries APR 05, 2023 NHTSA Recall No. : 23V-240 Manufacturer Recall No. : NR Manufacturer Information :
Manufacturer Name : Motor Coach Industries Address : 200 East Oakton Street
Des Plaines IL 60018
Company phone : 1-800-241-2947
Population :
Number of potentially involved : 140 Estimated percentage with defect : 100 %
Vehicle Information : Vehicle 1 : 2019-2021 Motor Coach Industries D45CRTLE, J3500, J4500 Vehicle Type : BUSES, MEDIUM & HEAVY VEHICLES Body Style : OTHER Power Train : NR
Descriptive Information : Recall population was determined based on coaches that received an optional rear mounted bike rack. Coaches without an optional bike rack are not affected.
Production Dates : AUG 01, 2019 – MAY 31, 2022 VIN Range 1 : Begin : 1M8ZDMBA9KP081004 End : 1M8ZDMNAXMP081141 โ Not sequential Description of Noncompliance :
Description of the Noncompliance :
On coaches with rear mounted bike racks, inward lighting angles required by FMVSS 108. FMVSS 1 : 108 – Lamps, reflective devices, and assoc. Equipment FMVSS 2 : NR
Description of the Safety Risk : Rear illumination and visibility for approaching traffic may be reduced with bikes installed on the rack. Reduced visibility may increase the likelihood of a crash.
Description of the Cause : With bikes installed on the bike rack, the bike frame/seat/etc. block the inward angle illumination requirements of FMVSS 108. Identification of Any Warning
that can Occur : No known pre-warning.
Involved Components : Part 573 Safety Recall Report 23V-240 Page 2 Component Name 1 : INSTL-SWINGLOCK BIKE RACK
Component Description : Bike rack, rear mount, 5 position Component Part Number : 951488 Supplier Identification : Component Manufacturer
Name : Motor Coach Industries Address : NR
Des Plaines Illinois
Country : United States Chronology :
-Late 2022, MCI receives a request from a customer to install a 5-position bike rack on the rear of the coach
-February 2023, as design releases occur, it was noted there was a missing validation report for FMVSS 108 with the bike rack installed.
-Early-March 2023 MCI arranges for an outside test facility to check lighting with the rack installed to FMVSS 108.
-Mid-March 2023 โ testing indicated likely non-compliance when bikes are mounted on the rack, where the inward angle lighting was impacted, in noncompliance with 108 6.1.3 Mounting location,
—6.1.3.1, โโฆcomplies with all photometric requirementsโฆwith all obstructions considered.โ
-March 24, 2023 โ analysis continues on the lighting angle candela readings via coach CAD models
-March 27, 2023 โ engineering determined the bikes, as mounted, are deemed โobstructionsโ and would affect the inboard angle requirements.
-March 31, 2023 โ issue was raised to the Vehicle Safety Committee where a recall determination was made Description of Remedy :
Description of Remedy Program : Motor Coach Industries (MCI) will provide instructions and a kit to add
lighting to the bike rack to ensure compliance when bikes are loaded to the rack. How Remedy Component Differs from Recalled Component : MCI will perform the installation of the kit for customers. If customers perform the installation, MCI will reimburse through our normal Warranty process.
The additional lights will be noticeable on the racks – currently no racks are equipped with ancillary lights. The information contained in this report was submitted pursuant to 49 CFR ยง573 Part 573 Safety Recall Report 23V-240
Page 3
The information contained in this report was submitted pursuant to 49 CFR ยง573
Identify How/When Recall Condition was Corrected in Production :
Current production will have the lighting kit installed prior to delivery to customers. Recall Schedule :
Description of Recall Schedule : MCI plans to issue recall letters in May 2023 once the final kit is validated
and material is available.
Planned Dealer Notification Date : MAY 01, 2023 – MAY 31, 2023
Planned Owner Notification Date : MAY 01, 2023 – MAY 31, 2023
* NR – Not Reported
SEOCONTENT-END
Last update on 2025-04-15 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.