โThis site contains affiliate links for which OEMDTC may be compensatedโ |
April 6, 2023 NHTSA CAMPAIGN NUMBER: 23V246000
Missing Wiring Protection May Cause Fire
An electrical short circuit increases the risk of a fire. Additionally, a vehicle fire may require an evacuation procedure in an uncontrolled traffic situation, increasing the risk of injury to passengers.
NHTSA Campaign Number: 23V246
Manufacturer Prevost Car (US) Inc.
Components ELECTRICAL SYSTEM
Potential Number of Units Affected 3
Summary
Prevost Car (US) Inc. (Prevost
) is recalling certain 2023 X3-45 VIP Entertainer motor coaches. The grommet that protects the electrical power distribution cables passing through a metallic panel was not installed, allowing the cables to chafe on the edges of the panel and potentially short circuit.
Remedy
Owners are advised not to drive their vehicles until the remedy is performed. Prevost will inspect and install the grommet, if necessary, free of charge. Owner notification letters were mailed May 8, 2023. Owners may contact Prevost
customer service at 1-866-870-2046. Prevost
’s number for this recall is SR23-14.
Notes
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.nhtsa.gov.
Prevost Technical Publications
SR23-14
Power Cable Missing Grommet
DESCRIPTION
On vehicles affected by this recall, electrical power distribution cables routed through a metallic panel are not protected by a grommet. The wiring conductor insulation could become damaged by chafing on the edges of the panel, potentially causing a short-circuit.
MATERIAL
Order Kit SR23-14 which contains the following parts:
Part No. | Description | Qty |
069464 | PROTECTOR FOR CABLE PASSAGE | 1 |
504016 | CABLE TIE, NYLON BLK (LIGHT-HEAVY) | 6 |
504637 | CABLE TIE, NYLON BLK (STD) | 6 |
Other material that may be required:
Part No. | Description | Qty |
680066 | GLUE CYANO. ADBOND 5014S, 25 GR. | As Req. |
564099 | CLOTH TAPE, PROTECT. 150ยชC – BLACK | As Req. |
Chronology :
2023-03-23 Issue identified in production during the final verification at the end of the assembly line.
2023-03-23 Internal Prevost investigation was opened to identify the root cause and to determine if vehicles were delivered with this issue.
2023-03-30 Delivery Stop was issued to stop the delivery of new vehicles until the investigation is completed and corrective actions are implemented.
2023-03-31 Case was presented on Volvo PSWG. Decision made to raise the potential safety issue to Volvo
Product Safety Committee (PSC) for review and determination.
2023-03-31 Internal campaign was launched to solve the issue on all vehicles in production before being delivered.
2023-03-31 Prevost communicated with all potentially affected vehicle owners to advise them not to drive their vehicles until they are remedied.
2023-03-03 Case was presented to Volvo PSC. It was concluded that there was a safety related defect, and that a recall combined with a โDo Not Drive Warningโ are needed.
2023-04-06 Safety Recall report submitted to authorities.
No warranty claims related to this issue. No field reports, incidents, accidents, injury, or fatality were reported.
1 Affected Product
Vehicle
MAKE | MODEL | YEAR |
PREVOST![]() | X3-45 VIP | 2023 |
6 Associated Documents
Recall Acknowledgement
RCAK-23V246-5001.pdf 645.335KB
Defect Notice 573 Report
RCLRPT-23V246-8674.PDF 331.246KB
Safety Bulletin
RCSB-23V246-8679.pdf 786.112KB
ISSUED Owner Notification Letter(Part 577)
RCONL-23V246-5254.pdf 238.693KB
Recall 573 Report – 04/28/2023
RCLRPT-23V246-4419.PDF 214.64KB
Recall Quarterly Report #1, 2023-2
RCLQRT-23V246-6262.PDF 211.134KB
Latest Recalls Documents
- High Quality: Made of high quality material,are durable and has longer service life, high temperature resistance, less affected by the negative effects of UV light and ozone, flame retardant and insulation
- Detailed Size: 1/4inch or 6.4mm=40pcs grommet, 5/16inch or 7.9mm=40pcs grommet, 3/8inch or 9.5mm=40pcs grommet, 7/16inch or 11.11mm=30pcs grommet, 1/2inch or 12.7mm=25pcs grommet, 5/8inch or 15.9mm=10pcs grommet, 3/4inch or 19.1mm=5pcs grommet, 7/8inch or 22.22mm=5pcs grommet, 1inch or 25.4mm=5pcs grommet
- Wide Application: Use for wall hole, workshops, plumbing services, wires, cable, firewall, spray, cylinder, valve, automotive, car, pump, electrical appliance, chemical pipe, water pipe,etc
- Handy Packing: Very clear classics plastic case include 9 grids that keep each size separated and organized make you easy to find correct size very quickly
- Customer Service: We strive to provide you with best quaility product and customer experience as possible. Any questions, please contact us directly
- HIGH QUALITY MATERIAL - Rubber grommets are made of flexible and durable rubber material, they are of good electric resistance capability. Corrosion resistance, high temperature resistance, less affected by the negative effects of UV light and ozone, more durable and tear-resistant.
- SIZE & QUANTITY - 12pcs 5/8" Drill Hole, 10pcs 13/16"Drill Hole, 10pcs 7/8"Drill Hole, 8pcs 1" Drill Hole, 8pcs 1-3/16" Drill Hole, 4pcs 1-1/2" Drill Hole.
- PACKING - Total 6 Sizes 52pcs Double Sided Rubber Grommet packed in a clear plastic case, makes it easy to find correct item quickly, saves your time of running around looking for a particular size grommet.
- EASY TO USE - Each rubber grommet is flexible and can be easily installed according to the thickness of the cable. You can choose a right size grommet in the kit and cut the diameter according to your use and then easily snap it directly into the drill hole.
- WIDE APPLICATION - Rubber grommets help protect wires and cables from sharp metal edges and eliminate wire risks and protect cables from dust and rain. Suitable for electrical cabinet, box outlet protection seal and so on.
- Great Variety of Sizes: 188 Pcs of the most commonly used sizes assorted rubber grommet assortment kit.
- High Quality: Rubber washers are made of flexible and durable rubber material, they are of good electric resistance capability.
- Easy To Use: Wire grommets are quicker and easier to install since they can be placed on one side only.
- Wide Range of Applications: Very useful for auto and other projects where wiring cable needs to be run through metal or plastic openings.
- Packaging Includes: 1/4" (40pcs), 5/16" (40pcs), 3/8" (40pcs), 7/16" (25pcs), 1/2" (20pcs), 5/8" (5pcs), 7/8" (10pcs-(5pcs closed Gasket+5pcs Eyelet Ring Gasket)), 1" (8pcs-(5pcs Eyelet Ring Gasket+3pcs closed Gasket)).
- ๐ต BRILLIANT QUALITY: Our rubber grommets automotive are manufactured with high quality rubber for greater flexibility and resilience, resistant weather, tear, corrosion, it does not dry up or crack and come lose easily and to protect your cables, cords, and pipes. These flexible blind automotive rubber grommet kit fit all your vehicles from cars and trucks to motorcycles and boats, Say goodbye to the electrical damage caused by water and dust entering the inside of the hood through the holes.
- ๐ต GREAT FUNCTION: Closed rubber grommets are commonly used to protect or cover holes and to protect cables or wires from sharp corners or edges, SAFELY and EFFECTIVELY GRIPS WIRE to protect against fire hazards. firewall grommets automotive โare also important parts in automotive applications, it can also effectively reduce vibration and are used to seal different important under-the-hood and body applications.
- ๐ต WIDE APPLICATION: Rubber grommet assortment kit is useful in many professions like plumbers, mechanics, electricians, DIY'er, etc, used to fit parts together for appliances such as Automotive, RV, Boat, valve, pump, landscaping wiring, furniture, radar detector, dash/rear view Backup camera, GPS navigation, audio speakers and wiring of different mechanisms, etc.
- ๐ต WHAT WILL YOU GET: 200 pieces of the most commonly used 7 different rubber plugs for holes assorted sizes - 7/25, 3/8, 1/2, 5/8, 3/4, 7/8, and 1 inch. - Organized in a divided case so you can quickly and easily size your Rubber grommets - to meet all your needs with a rubber grommet tool kit all-purpose
- ๐ 100% SATISFACTION WITH NO WORRIES: If you have any questions or are dissatisfied with our rubber grommets, please feel free to contact us and we will reply to you within 24 hours. Weโre not just sure that you will love these rubber grommet kit, we're truly dedicated to your 100% satisfaction.
- Double-sided Rubber Gaskets are rubber materials, strong flexibility, folding resistance, abrasion resistance, pressure resistance,high temperature resistance, aging resistance, long lasting,cushioning and shock absorption, safe, non-toxic and tasteless, with exquisite appearance.
- Product Features:The black rubber gasket not only helps us solve the trouble of wire and cable management, but also prevents the wire and cable from touching the pointed metal and protects the cable from dust and rain.
- Easy To Use:We equip the product with a retractable utility knife,when in use, you can adjust the diameter of the rubber gasket according to the thickness of your own cable,and cut freely.
- Wide Use:Firewall plug gaskets can be used in electrical appliances,office equipment,pumps,cylinders,valves,various pipelines,etc.
- What You Will Get:1-1/2inch*2Pcs,5/8inch*8Pcs,1-3/16inch*4Pcs,1inch*6Pcs,7/8inch*6Pcs,13/16inch*6pcs + 1Pcs retractable utility knife.A total of 52Pcs Rubber Grommet,enough replacement to suit your needs.The are placed in a transparent plastic box, each size of rubber grommet are sorted separately which is easy to transport and distinguish.
- 1. FLEXIBLE AND EASY TO USE: They are cut precisely and very flexible, easy to fit into a hole, and flexible to install without cracking. By default, they are completely closed and can be used just to plug a hole which is no longer in use, but it can be easily opened up by tearing a pre-cut (X) in the middle of a grommet to allow wires to pass through.
- 2. ENVIRONMENTAL MATERIAL: Our rubber grommets for wiring are made of environmentally friendly and high-quality rubber materials. They are durable, non-toxic, environmentally friendly and good for your health. Smooth and waterproof, suitable for indoor and outdoor use.
- 3. FLAME RETARDING: We use premium retardant materials. Which make the rubber plug hole grommet automatically extinguish when leaving an open flames, which can successfully prevent fire hazards.
- 4. DOUBLE-SIDED DESIGN: Our flexible rubber grommet for wiring helps to protect wire and cable from pointed metal edges as well as reducing the risk of wire and protecting the cable from dust and rain to a certain degree.
- 5. QUANTITY AND SIZE: These electrical wire gaskets come in a very convenient sectioned tray with separate size compartments, which makes it easy to find the size you need. You will get 46 pcs rubber grommets in 6 common sizes, including 5/8in 9pcs, 13/16in 7pcs, 7/8in 7pcs, 1in 8pcs, 1-3/16in 10pcs, 1-6/16in 3pcs and 1pcs knife.
- Wide Application โ Rubber grommets are commonly used to protect or cover holes and to protect cables or wires from dust rain or sharp corners and edges. Rubber grommets are also important parts in automotive applications.
- Quality โ The Rubber Grommets are made of soft, flexible, and durable rubber material. They are non-flammable, weather-resistant, tear-resistant, and high heat resistance. It can also handle bigger temperature spans than other types of grommets.
- Easy To Use โ These rubber grommets are quicker and easier to install since they can be placed on one side only. The grommets are perfect for small or long cords and cables. When installed, the opening remains sealed until the membrane is pushed out.
- Handy Packing โ The grommets come with clear plastic divided organizer case that keeps the rubber grommets organized and in one place. It makes you easy to find the correct size grommets quickly. Never lose a grommet again with this organizer case.
- HIGH QUALITY - Rubber grommets are made of flexible and durable rubber material, they are of good electric resistance capability. Corrosion resistance, high temperature resistance, less affected by the negative effects of UV light and ozone, more durable and tear-resistant.
- SIZE - 1/4" (40pcs), 5/16" (40pcs), 3/8" (40pcs), 7/16" (25pcs), 1/2" (20pcs), 5/8" (10pcs), 7/8" (5pcs), 1" (5pcs)
- HANDY PACKING - Clear plastic case makes it easy to find correct item quickly, saves your time of running around looking for a particular size grommet.
- EASY TO USE - Rubber Grommets are quicker and easier to install since they can be placed on one side only. It is not necessary to reach the opposite side of the installation to attach a lock nut.
- WIDE APPLICATION - Fit for automotive, car, cylinder, valve, pump, electrical appliance, chemical pipe, spray, water pipe, plumbing, and PC hardware/piano repair, decoration, etc.
- ๐ฅ ใWhat You Getใ------- In the kit, you will get 140pcs black rubber grommet assortment in total. 25Pcs 2/13" eyelet ring gasket, 20Pcs 1/5" eyelet ring gasket, 20Pcs 5/16" eyelet ring gasket, 20Pcs 3/8" eyelet ring gasket, 15Pcs 1/2" eyelet ring gasket, 15Pcs 3/4" eyelet ring gasket, 15Pcs 13/16"eyelet ring gasket, 10Pcs 1" eyelet ring gasket. We provide you with 8 different sizes eyelet ring gasket, which can meet with your various needs.
- ๐ฅ ใHigh-quality Materialใ------- Rubber grommets are made of flexible and durable rubber material, they are of good electric resistance capability. Corrosion resistance, high temperature resistance, less affected by the negative effects of UV light and ozone, more durable and tear-resistant. So it can be used for a long time and can solve the problem of long-term wire protection.
- ๐ฅ ใWide Applicationsใ------- Our eyelet ring gasket not only suitable for various wires protection, but also fit for automotive, car, cylinder, valve, pump, electrical appliance, chemical pipe, spray, water pipe, plumbing, and PC hardware/piano repair, decoration, etc. Buying them is super valuable and meets your various needs in different scenarios.
- ๐ฅ ใEasy to Useใ------- Each rubber wire grommet is flexible and enables simple installation. Just choose the appropriate rubber grommets based on the size of the hole, don't need for additional tools can easily snap the rubber grommet directly into the drill hole.
- ๐ฅ ใSuper Valueใ------- Choosing us is to save you money. We also provide you with a different size from other rubber grommets, so that you can install the rubber grommets for smaller holes. Super value๏ผ
- 280 PIECE SET: We offer 8 different sizes of rubber grommets kit, more than enough for your use in any scenario, 1/4" (120pcs), 5/16" (60pcs), 3/8" (40pcs), 7/16" (25pcs), 1/2" (20pcs), 5/8" (5pcs), 7/8" (5pcs), 1" (5pcs).
- SUPERIOR QUALITY: Our rubber grommet kit are manufactured with first-rate rubber for greater flexibility and resilience, withstanding wear, tear, heat, light, electric current, and acid to protect your cables, cords, and pipes.
- HANDY PACKING: Rubber grommets for wiring, come with clear plastic divided organizer case that keeps the rubber grommets organized and in one place. It makes you easy to find the correct size grommets quickly.
- WIDE COMPATIBILITY: Rubber grommet assortment kit is useful in many professions like plumbers, automotive, car, cylinder, valve, pump, electrical appliance, chemical pipe, spray, water pipe, plumbing, and PC hardware/ piano repair, decoration, etc.
- SATISFACTION GUARANTEE: For whatever reason, if you are not satisfied with our rubber grommets, just contact us through amazon. Itโs superior quality with an unbeatable guarantee. Why keep looking when youโve found your solution right here!
SEOCONTENT-START
Writer: mg
SAFETY
RECALL
SR23-14
DATE :
May 2023
SECTION : 06 ELECTRICAL
SUBJECT:
Power Cable Missing Grommet
First Release
04-03-2023
APPLICATION
NOTICE TO SERVICE CENTERS
Verify vehicle eligibility by checking warranty bulletin status with SAP or via ONLINE WARRANTY SYSTEM available on Service / Warranty tab of Prevost website.
Model
VIN
X3-45 VIP commercial use
Model Year: 2023
2PCCS3496PC736879, 2PCCS3492PC736880, 2PCCS3494PC736881, 2PCCS349XPC736884
This Safety Recall does not necessarily apply to all the above-mentioned vehicles. Some vehicles may also have been modified before delivery. The owners of the vehicles affected by this recall will be advised by a letter indicating the Vehicle Identification Number (VIN) of each vehicle concerned.
DESCRIPTION
On vehicles affected by this recall, electrical power distribution cables routed through a metallic panel are not protected by a grommet. The wiring conductor insulation could become damaged by chafing on the edges of the panel, potentially causing a short-circuit.
MATERIAL
Order Kit SR23-14 which contains the following parts:
Part No.
Description
Qty
069464
PROTECTOR FOR CABLE PASSAGE
1
504016
CABLE TIE, NYLON BLK (LIGHT-HEAVY)
6
504637
CABLE TIE, NYLON BLK (STD)
6
SR23-14
Page 2 / 7
Writer: mg
Other material that may be required:
Part No.
Description
Qty
680066
GLUE CYANO. ADBOND 5014S, 25 GR.
As Req.
564099
CLOTH TAPE, PROTECT. 150ยชC – BLACK
As Req.
NOTE
Material can be obtained through regular channels.
SAFETY PRECAUTIONS
โข Eye protection should always be worn when working in a shop.
โข Rules for Personal Protection Equipment should always be respected. Wear your PPE including but not limited to the following:
Safety First!
PROCEDURE
DANGER
Park vehicle safely, apply parking brake, stop the engine. Prior to working on the vehicle, set the ignition switch to the OFF position and trip the main circuit breakers equipped with a trip button. On Commuter type vehicles, set the battery master switch (master cut-out) to the OFF position.
Lockout & Tag out (LOTO) must be performed during set-up, maintenance or repair activities. Refer to your local procedure for detailed information regarding the control of hazardous energy.
SR23-14
Page 3 / 7
Writer: mg
1. Locate the missing grommet location in the rear electrical compartment.
โข Open the vehicle curb side engine door.
โข Open the rear electrical compartment (next to the batteries).
โข In the compartment, the missing grommet must be installed in the cable pass through hole located at the top right corner of the compartment (hidden behind the battery equalizer).
SR23-14
Page 4 / 7
Writer: mg
2. Cut all the cable ties holding the power cables passing through the hole.
3. Make sure that the cables insulation is not damaged.
โข If damage is noticed, replace the cable(s) before installing the grommet (do not repair power cable(s)).
4. Cut the supplied 069464 cable protector (grommet).
โข Slice the grommet with a slant cut to allow the insertion of the cables.
SR23-14
Page 5 / 7
Writer: mg
5. Install the grommet in the electrical compartment.
โข Pass the cables one by one in the sliced cable protector.
โข Slide the cable protector in the wall opening.
โข Place the slanted cut at -/+ 75deg from top (to clear the installed T-mount).
6. Solidify the cable protector installation.
โข Put a few drop of 680066 glue (or equivalent super glue) to โweldโ the slanted cut of the cable protector.
โข Add some 564099 cloth tape over the re-glued cut area as shown.
7. Secure the power cables.
โข Re-attach the power cables using the supplied 504016 & 504637 cable ties, make sure the cables are secure that there is no contact sharp edges.
SR23-14
Page 6 / 7
Writer: mg
PARTS DISPOSITION
DO NOT RETURN THE REPLACED PARTS. Discard waste according to applicable environmental regulations (Municipal/State[Prov.]/ Federal)
WARRANTY
This modification is covered by Prevostโs normal warranty. We will reimburse you the parts and 1/2 hour (0.5 of labor upon receipt of a completed A.F.A. Please submit claim via our Online Warranty System, available at www.prevostcar.com (under service \ warranty section). Use Claim Type: โBulletin/Recallโ and select โโSafety Recall SR23-14 “.
Should you only wish to close the safety recall (without reimbursement), fill-in the โโSafety Recall Certification Sheetโโ provided with this bulletin and return it to our warranty department by Email at prevost.onlinewarranty@volvo
.com or by fax at 418-831-9301.
OTHER
VBC Bulletin
N/A
Access all our Service Bulletins on http://techpub.prevostcar.com/en/
or scan the QR-Code with your smart phone.
E-mail us at technicalpublications_prev@volvo.com and type โADDโ in the subject to receive our warranty bulletins by e-mail.
Fail Code 06.15
Defect Code
09
Syst.Cond
R
Causal Part
069464
Writer: mg
VEHICLE SERIAL NUMBER:
PERFORMED BY
OWNER/OPERATOR
We hereby certify that Safety Recall Instructions with regard to Safety Recall SR23-14 have been performed.
Name:
Name:
Addr:
Addr:
Phone:
Phone:
Fax:
Fax:
Signature :
Signature :
Date:
Date:
If the information mentioned above is incorrect or you are not the owner of this vehicle anymore, please fill this section and return to sender.
NEW OWNER:
BUSINESS:
ADDRESS (including County):
TELEPHONE:
FAX:
Please return this completed document with your A.F.A. form
Safety Recall
Certification Sheet
(Ref: SR23-14 )
**************************************************************************************************************
US recall notif letter
PREVOST SAFETY RECALL SR23-14
NHTSA SAFETY RECALL # 23V-246
May 2023
ยซcustomerยป SR23-14
ยซaddยป ยซpoยป
ยซcityยป, ยซstยป ยซzipยป
USA
IMPORTANT SAFETY RECALL
This notice applies to your vehicle(s), see VIN list below.
Dear Customer,
This notice is sent to you in accordance with the National Traffic and Motor Vehicle Safety Act.
Prevost Car US Inc. has decided that a defect which relates to motor vehicle safety exists in certain 2023 X3-45 VIP Entertainer vehicles.
DEFECT DESCRIPTION
On certain vehicles, electrical power distribution cables routed through a metallic panel were not protected by a grommet. The wiring conductor insulation could become damaged by chafing on the edges of the panel, potentially causing a short-circuit which could increase the risk of a fire.
SAFETY RISK
A fire increases the risk of injury to vehicle occupants and persons around the vehicle. A fire may also require a passenger evacuation in traffic and other potential hazards, which increases the risk of injury.
IDENTIFICATION OF ANY WARNING THAT CAN PRECEDE
There is no warning with this issue.
US recall notif letter
REMEDY PROGRAM
Prevost has released a repair procedure to remedy the affected vehicle population with a replacement grommet. The service and required parts will be provided free of charge.
According to our records, you are the registered owner of the following vehicles involved in this safety recall SR23-14 :
ยซVIN1ยป
ยซVIN2ยป
ยซVIN3ยป
ยซVIN4ยป
WHAT YOU NEED TO DO
In addition to the Safety Recall, Prevost issued a โDo Not Drive Warningโ for this defect until the vehicles are remedied.
Please contact your nearest Prevost Customer Support Manager and refer to Safety Recall SR23-14 to confirm the status of your vehicle & instruct you of the next steps required to have it serviced.
You will find your Customer Support Manager at this address:
https://prevostcar.com/contact/contact-your-team
Optionally, you may have the work performed by qualified personnel of your choice, following Safety Recall SR23-14 available on Prevost Technical Publications web site at this address: http://techpub.prevostcar.com/en/
The time to inspect and repair your vehicle if required is approximately half an hour (0.5h).
NOTICE REGARDING LEASED VEHICLES
If you are a Lessor of vehicles subject to this Notice, you have an obligation under Federal Law to send a copy of this Notice to all Lessees within 10 days.
PRE-NOTIFICATION REMEDIES
If you have previously paid for repairs as a result of this issue, you may be entitled to recovery of those expenses. Prevost Car US will reimburse the claimant by check for the reasonable amount paid for repairs (i.e. the cost of parts, labor, disposal fees and taxes) that addressed the defect as stated in the safety recall notification. To qualify, repairs must have been completed no earlier than one year prior to the release of the recall and no later than 10 days after the release of the recall mailing of the initial customer notification letter pertaining to the recall. To get reimbursed, please file an online warranty claim following normal Campaign procedures if you are a registered customer, otherwise, contact the Prevost
Warranty Department at 1-866-870-2046 for reimbursement instructions.
US recall notif letter
REIMBURSEMENT OF PRE-NOTIFICATION REMEDIES
When a Prevost vehicle is affected by a safety recall and the owner/purchaser (claimant) has the safety-related defect or FMVSS regulatory noncompliance remedied at their own expense prior to receiving the manufacturer notification of the safety recall, Prevost
Car (US) Inc. will reimburse the owner/purchaser for the reasonable amount paid (i.e. the cost of parts, labor, disposal fees and taxes) that addressed the safety-related defect or FMVSS regulatory noncompliance as described in the safety recall notification. To qualify, repairs must have been completed no earlier than one year prior to the release of the safety recall (notification to the government) and no later than 10 days after the last mailing of the initial customer notification letter pertaining to the recall. To get reimbursed, please file an online warranty claim following normal campaign procedure if you are a registered customer, otherwise, please contact the Prevost
Warranty Department at 1-866-870-2046 for reimbursement instructions.
CHANGE OF ADDRESS OR OWNERSHIP
If your address has changed, or you no longer own the vehicle(s), please help us update our records. Use the link below to access the Prevost Warranty Support web page https://prevostcar.com/contact/warranty
Click on the link โChange of address or ownershipโ, fill the form, save it and email the file to prevost.warranty@volvo
.com
ASSISTANCE
If you need assistance, please contact your nearest Prevost Service Center. You will find the Prevost
Parts & Service Centers location at this address:
https://prevostcar.com/contact/parts-service-center
COMPLAINTS
You may submit a complaint if you believe that Prevost Car US has failed or is unable to remedy the defect without charge or within a reasonable time.
You may submit the complaint to the Administrator of the National Highway Traffic Safety Administration located at 1200 New Jersey Avenue SE, Washington, DC 20590, USA or call the toll-free Vehicle Safety Hotline at: 1-888-327-4236, (TTY): 1-800-424-9153) or go to http://www.safercar.gov
We regret any inconvenience this may cause to your operations but hope you will appreciate our sincere efforts to demonstrate Prevost’s commitment to provide our customers with the best possible product.
Truly yours,
Prevost Service Team
**************************************************************************************************************
OMB Control No.: 2127-0004
Part 573 Safety Recall Report 23V-246
The information contained in this report was submitted pursuant to 49 CFR ยง573
Manufacturer Name : Submission Date :
Prevost Car (US) Inc. APR 06, 2023 NHTSA Recall No. : 23V-246 Manufacturer Recall No. : NR Manufacturer Information :
Manufacturer Name : Prevost Car (US) Inc.
Address : 201 South Avenue
South Plains NJ 07080 Company phone : 908-222-7211
Population :
Number of potentially involved : 3
Estimated percentage with defect : 100 %
Vehicle Information : Vehicle 1 : 2023-2023 Prevost X3-45 VIP Entertainer Vehicle Type : BUSES, MEDIUM & HEAVY VEHICLES Body Style : OTHER Power Train : DIESEL
Descriptive Information : The population was determined based on the production period and location as it is a production issue. The concerned vehicles are certain MY2023 Prevost X3-45 VIP Entertainer vehicles manufactured during the indicated production dates. The recalled products are limited to these specific vehicles since they are the only X3-45 VIP Entertainer potentially delivered without a grommet to protect the electrical cables. A total of 3 MY2023 Prevost
X3-45 VIP Entertainer vehicles are affected by the recall.
Production Dates : FEB 09, 2023 – FEB 15, 2023
VIN Range 1 : Begin : End : Not sequential Description of Defect :
Description of the Defect : On certain vehicles, electrical power distribution cables routed through a metallic panel were not protected by a grommet. The wiring conductor insulation could become damaged by chafing on the edges of the panel, potentially causing a short-circuit which could increase the risk of a fire.
FMVSS 1 : NR FMVSS 2 : NR
Description of the Safety Risk : A fire increases the risk of injury to vehicle occupants and persons around the vehicle. A fire may also require a passenger evacuation in traffic and other potential hazards, which increases the risk of injury. In addition to the Safety Recall, Prevost issued a โDo Not Drive Warningโ for
this defect until the vehicles are remedied. Part 573 Safety Recall Report 23V-246 Page 2 Prevost has not received any reports of death or injury associated with this defect. Therefore, we consider this as a proactive measure to protect the public from the potential risk associated with this defect.
Description of the Cause : During the vehicle manufacturing, Prevost assembly line workers did not install grommets on certain vehicles (production issue). Identification of Any Warning
that can Occur : There is no warning with this issue. Involved Components : Component Name 1 : Grommet
Component Description : Protection for cable feed through Component Part Number : 069464 Supplier Identification : Component Manufacturer
Name : NR Address : NR
NR
Country : NR Chronology :
2023-03-23 Issue identified in production during the final verification at the end of the assembly line. 2023-03-23 Internal Prevost investigation was opened to identify the root cause and to determine if vehicles were delivered with this issue. 2023-03-30 Delivery Stop was issued to stop the delivery of new vehicles until the investigation is completed and corrective actions are implemented. 2023-03-31 Case was presented on Volvo
PSWG. Decision made to raise the potential safety issue to Volvo
Product Safety Committee (PSC) for review and determination. 2023-03-31 Internal campaign was launched to solve the issue on all vehicles in production before being delivered. The information contained in this report was submitted pursuant to 49 CFR ยง573 Part 573 Safety Recall Report 23V-246
Page 3
The information contained in this report was submitted pursuant to 49 CFR ยง573
2023-03-31 Prevost communicated with all potentially affected vehicle owners to advise them not to drive their vehicles until they are remedied. 2023-03-03 Case was presented to Volvo
PSC. It was concluded that there was a safety related defect, and that a recall combined with a โDo Not Drive Warningโ are needed. 2023-04-06 Safety Recall report submitted to authorities. No warranty claims related to this issue. No field reports, incidents, accidents, injury, or fatality were reported.
Description of Remedy :
Description of Remedy Program : Prevost will inspect all concerned vehicles and, if required, install the
missing grommet. Letters will be sent to customers to inform them on how to proceed. Prevost will execute this correction free of charge (parts and labor) for the customers. In case a customer has already inspected and corrected this defect before the safety recall has been launched, this customer will be reimbursed according to Prevost
reimbursement plan. How Remedy Component Differs from Recalled Component : Identify How/When Recall Condition was Corrected in Production : The issue concerns a component that was not installed on certain vehicles during manufacturing. After the remedy, the missing grommet will be installed on all vehicles.
The recall condition was corrected in production on March 31, 2023, when an internal campaign was launched. All vehicles are corrected prior to delivery. Recall Schedule :
Description of Recall Schedule : Please note that Prevost does not have a dealer network and the dates
entered for the planned dealer notification begin/end date are only to avoid NHTSA Recall Portal error while submitting the recall report.
On March 31, 2023, Prevost communicated with all potentially affected vehicle owners to advise them not to drive their vehicles until they are remedied.
Planned Dealer Notification Date : MAY 26, 2023 – MAY 26, 2023
Planned Owner Notification Date : MAY 26, 2023 – MAY 26, 2023
* NR – Not Reported
**************************************************************************************************************
OMB Control No.: 2127-0004
Part 573 Safety Recall Report 23V-246
The information contained in this report was submitted pursuant to 49 CFR ยง573
Manufacturer Name : Submission Date :
Prevost Car (US) Inc. APR 28, 2023 NHTSA Recall No. : 23V-246 Manufacturer Recall No. : SR23-14 Manufacturer Information :
Manufacturer Name : Prevost Car (US) Inc.
Address : 201 South Avenue
South Plains NJ 07080 Company phone : 908-222-7211
Population :
Number of potentially involved : 3
Estimated percentage with defect : 100 %
Vehicle Information : Vehicle 1 : 2023-2023 Prevost X3-45 VIP Entertainer Vehicle Type : BUSES, MEDIUM & HEAVY VEHICLES Body Style : OTHER Power Train : DIESEL
Descriptive Information : The population was determined based on the production period and location as it is a production issue. The concerned vehicles are certain MY2023 Prevost X3-45 VIP Entertainer vehicles manufactured during the indicated production dates. The recalled products are limited to these specific vehicles since they are the only X3-45 VIP Entertainer potentially delivered without a grommet to protect the electrical cables. A total of 3 MY2023 Prevost
X3-45 VIP Entertainer vehicles are affected by the recall.
Production Dates : FEB 09, 2023 – FEB 15, 2023
VIN Range 1 : Begin : 2PCCS3496PC736879 End : 2PCCS3494PC736881 Not sequential Description of Defect :
Description of the Defect : On certain vehicles, electrical power distribution cables routed through a metallic panel were not protected by a grommet. The wiring conductor insulation could become damaged by chafing on the edges of the panel, potentially causing a short-circuit which could increase the risk of a fire.
FMVSS 1 : NR FMVSS 2 : NR
Description of the Safety Risk : A fire increases the risk of injury to vehicle occupants and persons around the vehicle. A fire may also require a passenger evacuation in traffic and other potential hazards, which increases the risk of injury. In addition to the Safety Recall, Prevost issued a โDo Not Drive Warningโ for
this defect until the vehicles are remedied. Part 573 Safety Recall Report 23V-246 Page 2 Prevost has not received any reports of death or injury associated with this defect. Therefore, we consider this as a proactive measure to protect the public from the potential risk associated with this defect.
Description of the Cause : During the vehicle manufacturing, Prevost assembly line workers did not install grommets on certain vehicles (production issue). Identification of Any Warning
that can Occur : There is no warning with this issue. Involved Components : Component Name 1 : Grommet
Component Description : Protection for cable feed through Component Part Number : 069464 Supplier Identification : Component Manufacturer
Name : NR Address : NR
NR
Country : NR Chronology :
2023-03-23 Issue identified in production during the final verification at the end of the assembly line. 2023-03-23 Internal Prevost investigation was opened to identify the root cause and to determine if vehicles were delivered with this issue. 2023-03-30 Delivery Stop was issued to stop the delivery of new vehicles until the investigation is completed and corrective actions are implemented. 2023-03-31 Case was presented on Volvo
PSWG. Decision made to raise the potential safety issue to Volvo
Product Safety Committee (PSC) for review and determination. 2023-03-31 Internal campaign was launched to solve the issue on all vehicles in production before being delivered. The information contained in this report was submitted pursuant to 49 CFR ยง573 Part 573 Safety Recall Report 23V-246
Page 3
The information contained in this report was submitted pursuant to 49 CFR ยง573
2023-03-31 Prevost communicated with all potentially affected vehicle owners to advise them not to drive their vehicles until they are remedied. 2023-03-03 Case was presented to Volvo
PSC. It was concluded that there was a safety related defect, and that a recall combined with a โDo Not Drive Warningโ are needed. 2023-04-06 Safety Recall report submitted to authorities. No warranty claims related to this issue. No field reports, incidents, accidents, injury, or fatality were reported.
Description of Remedy :
Description of Remedy Program : Prevost will inspect all concerned vehicles and, if required, install the
missing grommet. Letters will be sent to customers to inform them on how to proceed. Prevost will execute this correction free of charge (parts and labor) for the customers. In case a customer has already inspected and corrected this defect before the safety recall has been launched, this customer will be reimbursed according to Prevost
reimbursement plan. How Remedy Component Differs from Recalled Component : Identify How/When Recall Condition was Corrected in Production : The issue concerns a component that was not installed on certain vehicles during manufacturing. After the remedy, the missing grommet will be installed on all vehicles.
The recall condition was corrected in production on March 31, 2023, when an internal campaign was launched. All vehicles are corrected prior to delivery. Recall Schedule :
Description of Recall Schedule : Please note that Prevost does not have a dealer network and the dates
entered for the planned dealer notification begin/end date are only to avoid NHTSA Recall Portal error while submitting the recall report.
On March 31, 2023, Prevost communicated with all potentially affected vehicle owners to advise them not to drive their vehicles until they are remedied.
Planned Dealer Notification Date : MAY 26, 2023 – MAY 26, 2023
Planned Owner Notification Date : MAY 26, 2023 – MAY 26, 2023
* NR – Not Reported
SEOCONTENT-END
Last update on 2025-04-17 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.