August 2, 2023 NHTSA CAMPAIGN NUMBER: 23V543000
The fractured steering arm and tie rod can separate and fall to the ground, increasing the risk of a crash.
NHTSA Campaign Number: 23V543
Manufacturer Hyundai
Translead
Components STEERING
Potential Number of Units Affected 2
Summary
Hyundai
Translead is recalling certain 2022 V/T 53SW Q29485 VI2530154-AFJ Dry Van trailers equipped with Dexter
Smart-Steer 2.0 Axles with bolt-on steering arms. The steering arm may fracture during certain conditions, such as low speed and high side-loading.
Remedy
Dealers will install a new steering arm and additional welds, free of charge. Owner notification letters were mailed August 11, 2023. Owners may contact Hyundai
Translead customer service at 1-800-251-0871.
Notes
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.nhtsa.gov.
IMPORTANT SAFETY RECALL
October 14, 2022
Hyundai
Translead
685 De La Fuente Court
San Diego, CA 92154
Dear Sir or Madam,
Re: Safety Recall – Smart-Steer 2.0 Self-Steer Axle with 702887 Steer Arm
Dexter
Trailer Products of Canada Corporation (“Dexter
Canada” (Ingersoll Axles)) has determined that certain self steer axles installed or distributed by your company may contain a defect which could be a safety risk under certain conditions or applications. Accordingly, a recall (NHTSA ID 22E-080) to address this issue was initiated effective September 21, 2022. This potential defect and the remedy are detailed in the attached Service Bulletin SB015 dated September 21, 2022.
The affected axles are models of the Smart-Steer 2.0 self-steering axle with the 702887 bolt-on steer arm built from October 13, 2017 to October 30, 2022. Dexter
Canada has determined that under certain heavy loading conditions the steer arm attached to the knuckle can potentially shear. If this condition occurs, the upper section of the sheared steer arm will remain attached to the knuckle by the mounting bolts and lower section of the steer arm will remain attached to the tie-rod assembly but potentially drag along the ground. At no time will the vehicle become uncontrollable and the operator will be able to safely operate until they can secure the axle under the vehicle.
The repair, which is outlined in the Service Bulletin SB015 (attached), must be performed at a Dexter
Canada authorized facility and will be at no cost to the owner (Dexter
Canada will pay the cost of the prescribed repair).
Please provide all known owners of your trailers which contain an affected axle with a recall notice with the specific instructions for the repair, as well the locations and contact information for authorized repair facilities.
Your assistance with this matter is appreciated. Should you have any questions please contact Phil Schnurr directly at 226-242-5345 or email [email protected].
Sincerely,
R.W. Gelven,
VP of Product Engineering and Product Innovation
Chronology :
After Dexter
Axle Company reviewed recent claims with a key customer, a service bulletin was requested to address the customer issues. Upon further investigations and reviews, Dexter
Canada conducted an analysis of the failure mode and determined the material was not robust enough to withstand the higher loading events which may occur in this configuration. Re-design activities were initiated to define a steer arm design that will withstand the unique, higher load events based on collected road load data.
22E080 – Steering Arm May Fracture – Dexter Axle Smart-Steer 2.0 Self-Steering Axles
http://oemdtc.com/12201/22e080-steering-arm-may-fracture-dexter
-axle-smart-steer-2-0-self-steering-axles
1 Affected Product
Vehicle
4 Associated Documents
Recall Acknowledgement
RCAK-23V543-3535.pdf 646.211KB
Defect Notice 573 Report
RCLRPT-23V543-4699.PDF 213.839KB
Owner Notification Letter(Part 577) – Redacted
RCONL-23V543-5397.pdf 139.955KB
Notification of Recall 22E080
RCORRD-23V543-6972.pdf 239.986KB
Latest Recalls Documents
- MULTI PROCESS: Experience the convenience of a high-quality, budget-friendly 3-in-1 welding machine that masterfully handles Gasless Flux Core MIG/Stick/Lift TIG(additional 10-25 lift TIG torch required). This unit caters to a wide range of welding applications and meets your various welding needs.
- WELDING CAPACITY: With a robust 135 Amp output, this welder is capable of tackling mild steel workpieces up to 3/32 inch(2.5mm) thick. It is compatible with 2LB .030’’ and .035’’ welding wire. For Stick Welding, the Hot Start and Arc Force can be adjusted to enhance your welding experience.
- SYNERGIC CONTROL: The wire feeding speed is flexibly adjustable (030": 120-420 in/min;.035'': 120-308 in/min). When adjusting the wire feeding speed, the voltage will be automatically matched to a recommended value, and you can fine tune the voltage between -3V~3V. Ideal for both beginners and seasoned professionals.
- DIGITAL DISPLAY: The advanced digital display revolutionizes the welding interface, offering enhanced clarity and operational efficiency. Monitor the real-time current during welding for precise control.
- LIGHT&PORTABLE: Weighing just 11.4 lbs, this lightweight and compact welder is a breeze to transport, making it the perfect companion for on-the-go welding projects with its carrying handle.
- 4-IN-1 MIG Welder: The welder machine offers GAS MIG/Flux Core MIG/Lift TIG/ MMA welding modes (Note: WP-17V TIG torch must be purchased separately). It can easily handle welding stainless steel, carbon steel, and even thicker steel materials, meeting diverse welding requirements.
- TECHNICAL UPGRADE: This welding machine features upgraded MCU and IGBT technologies, enabling users to precisely adjust parameters for Synergy MIG (plate thickness, voltage, welding speed), Manual MIG (current, voltage), and MMA (hot start, arc force, etc.) while its dual-voltage design (110V/220V) supports flexible power switching (Caution: Ensure the screen is off and the fan has stopped before changing voltage settings).
- LARGE LED DISPLAY: With an exclusive human-computer interaction LED screen design, this welder provides accurate data display, allowing you to read it more easily and clearly without removing your helmet. This welder also has 2T/4T functions, which can seamlessly switch between continuous welding (4T) for long-term operations and trigger-controlled precision welding (2T) for fine operations, improving efficiency and flexibility.
- HIGH PERFORMANCE: The output current up to 165A, rated duty cycle: 60%, equipped with an upgraded cooling fan, the heat dissipation performance is improved by 30%, and can easily complete various welding tasks. This welder is capable of tackling mild steel workpieces up to 3/16” thick.
- SAFETY PROTECTION: The 165A MIG welder Built-in over-current protection, over-load protection, overheating, and over-voltage function that extend the lifespan of the machine.
- 5 IN 1 MULTIFUNCTIONAL: The MIG-205DS PRO is capable of Gas MIG/Flux Core MIG/Spool Gun Aluminum MIG/Lift TIG/Stick. (additional lift TIG torch required and spool gun required). This unit caters to a wide range of welding applications and meets your various welding needs.
- WELDING CAPACITY: With a robust 200 Amp output, 110V/220V dual voltage, this welder is in possession of reliable quality and stable performance. It's widely used in various scenarios, including automotive, construction, fabrication and DIY. It's suitable for welding thin and thick materials, such as steel, aluminum, and stainless steel.
- SYNERGIC&MANUAL MIG: The wire feeding speed is flexibly adjustable(Min:58 in/min; Max:858 in/min), when adjusting the wire feeding speed, the voltage will be automatically matched to a recommended value, and you can fine tune the voltage between -3V~3V. Great choice for beginners. You can also manually adjust the wire feeding speed and voltage according to your preferences, which is ideal for seasoned professionals.
- DIGITAL DISPLAY: The advanced digital display revolutionizes the welding interface, offering enhanced clarity and operational efficiency. Monitor the real-time current during welding for precise control.
- SAFETY PRIORITIZED: Our product features comprehensive safeguards, including automatic compensation for voltage fluctuation, robust protections against over-current, over-load, and over-heating, ensuring unparalleled user safety and device longevity.
- 【3-IN-1 WELDER】Compact 3 in 1 welder combines MIG welder, Stick, and Lift TIG welding machine functions to tackle a wide range of welding tasks. With 30–145A output and support for carbon and stainless steel (1–5mm), it’s ideal for home DIY, repairs, and outdoor metal work. (NOTE: TIG torch not included—please purchase separately)
- 【COMPACT & PORTABLE】This little welder machine 110V packs big power into just 7.5 lbs. Easy to carry with one hand, it’s perfect for your garage, yard, or job site. Don’t let its small size fool you—this compact welding machine delivers strong, reliable welds wherever you need them
- 【SMART SYNERGIC CONTROL】Perfect for beginners! Just set your wire diameter (.030"/.035") or amperage (30-145A)—the welder machine auto-adjusts voltage and wire speed. It even suggests metal thickness! Start welding like a pro, even if it’s your first time
- 【CLEAR LED DISPLAY】The bright digital screen shows real-time welding amperage and wire diameter, so you can monitor and adjust settings on your mig welder 110V without removing your mask. Intuitive and easy to use, it ensures consistent, high-quality welds—perfect for both experienced welders and weekend DIYers
- 【WHAT YOU WILL GET】Everything you need is in one box! Includes: 1*145A MIG welder 110V, 1*14AK MIG torch, 1* Ground clamp, 1*Electrode holder, 5* 2.5" Welding rods, 1*0.9mm flux core wire, 2* Contact tips, 1* Wrench, 1* Safety goggles, 1*Pair of gloves, 1*Hammer and 1* User manual. Plug it in and start your first project within minutes—no extra purchases required
- MULTIFUNCTIONAL: A 4-in-1 welder, capable of Flux Core MIG/Gas MIG/ Stick/Lift TIG (need to purchase extra tig lift torch). This unit caters to a wide range of welding applications and meets your various welding needs.
- WELDING CAPACITY: With a robust 160A output, 110V/220V dual voltage, this welder is in possess of reliable quality and stable performance. It's widely used in various scenarios, including automotive, construction, fabrication and DIY. This Welder can work with 2LB and 10LB spools of .030"(0.8mm) and .035" (0.9mm) solid core wire, flux core wire. It also performs well with most 6010, 6011, 6013 and 7018 rods in Stick Welding mode.
- SMART CONTROL: Smart control refers to Synergic control, when selecting different thicknesses or adjust the amperage, the recommend voltage and wire feeding speed will be automatically switched into. Great choice for beginners.
- MANUAL CONTROL: You can manually adjust the wire feeding speed and voltage according to your preferences, which is ideal for seasoned professionals and DIYers.
- LED DISPLAY: Advanced LED digital display, subverts the traditional visual experience, increases the visual clarity and improves the efficiency of the operation.
Last update on 2026-06-13 / Affiliate links / Images from Amazon Product Advertising API
SEOCONTENT-START
OMB Control No.: 2127-0004 Part 573 Safety Recall Report 23V-543 The information contained in this report was submitted pursuant to 49 CFR §573 Manufacturer Name : Hyundai
Translead Submission Date : AUG 02, 2023 NHTSA Recall No. : 23V-543 Manufacturer Recall No. : NR Manufacturer Information : Manufacturer Name : Hyundai
Translead Address : 8880 Rio San Diego Drive, #500 San Diego CA 92108-164 Company phone : 819-574-1500 Population : Number of potentially involved : 2 Estimated percentage with defect : 100 % Vehicle Information : Vehicle 1 : 2022-2022 V/T 53SW Q29485 VI2530154-AFJ Vehicle Type : TRAILERS Body Style : Power Train : NR Descriptive Information : – Dexter
Smart-Steer 2.0 self-steering axle with a bolt-on steer arm (702887) with a 3/4” drop to tie-rod location, built from October 13, 2017 to October 30, 2022. – Previous design level was a welded steering arm/knuckle asy and new design has stronger steer arm plus a weld. – A total of 2 defective components were installed in a total of (2) Hyundai
Translead trailers. Production Dates : MAY 20, 2021 – MAY 20, 2021 VIN Range 1 : Begin : 3H3V534KXNJ087001 End : 3H3V534K1NJ087002 Not sequential Description of Defect : Description of the Defect : Under low speed, high lateral loading events, the steer arm may fracture. FMVSS 1 : NR FMVSS 2 : NR Description of the Safety Risk : The fractured steer arm and attached tie rod will fall to the ground causing a risk for separation. There is no loss of control of the unit when this failure occurs. Description of the Cause : The material strength was not sufficient to withstand the high lateral loads Identification of Any Warning that can Occur : Independent castering of steer axle wheels and noise from dragging parts Involved Components : Part 573 Safety Recall Report 23V-543 Page 2 The information contained in this report was submitted pursuant to 49 CFR §573 Component Name 1 : 702887 Bolt-on steer arm Component Description : Smart-Steer 2.0 self-steering axle with the 702887 bolt-on steer arm Component Part Number : 702887 Supplier Identification : Component Manufacturer Name : Dexter
Axle Company Address : 2900 Industrial Parkway East PO Box 250 Elkhart Indiana 46516 Country : United States Chronology : After Dexter
Axle Company reviewed recent claims with a key customer, a service bulletin was requested to address the customer issues. Upon further investigations and reviews, Dexter
Canada conducted an analysis of the failure mode and determined the material was not robust enoungh to withstand the higher loading events which may occur in this configuration. Re-design activities were initiated to define a steer arm design that will withstand the unique, higher load events based on collected road load data. Description of Remedy : Description of Remedy Program : Service work will include the following steps: 1. Remove the existing steer arms and mounting hardware. 2. Clean mounting surface and surrounding surfaces to prepare for mounting of the new bolt-on steer arm and additional welds. 3. Grind a 3/16” chamfer along the mounting face edge. 4. Mount new design steer arms (Part # 703293-LH/RH) with supplied hardware and torque to 400 ft-lbs. 5. Add welds as shown on page three of this bulletin. How Remedy Component Differs from Recalled Component : New design has a higher strength material and welded to the steering knuckle Identify How/When Recall Condition was Corrected in Production : Implemented a new design with higher strength material as well as an additional weld connecting the arm to the knuckle into production at Dexter
Canada on 30-October-2022. Part 573 Safety Recall Report 23V-543 Page 3 The information contained in this report was submitted pursuant to 49 CFR §573 Recall Schedule : Description of Recall Schedule : Letter will be issued to customer no later than 04-Aug-2023 Planned Dealer Notification Date : NR – NR Planned Owner Notification Date : AUG 02, 2023 – AUG 04, 2023 * NR – Not Reported
**************************************************************************************************************
Hyundai
Translead 8880 Rio San Diego Drive, Suite 600 San Diego CA 92108 800-251-0871 www.translead.com IMPORTANT SAFETY RECALL NHTSA Campaign # 23V-543 This notice applies to your Hyundai
Translead Trailers on BOM#30017442 (2 units). VIN list attached. August 11th, 2023 Dear This notice is sent to you in accordance with the National Traffic and Motor Vehicle Safety Act. Hyundai
Translead has decided that a defect which relates to motor vehicle safety exists in certain 2022 dry van trailers. Important! – Your trailer(s) fall within the recall population – You should avoid use and schedule an appointment with Dexter
Axle Company to have your unit inspected. Why is a recall being conducted? Under low speed, high lateral loading events, the bolt-on steer arm of the Dexter
Smart Steer 2.0 self-steering axle may fracture. The fractured steer arm and attached tie rod will fall to the ground causing a risk for separation leading to an accident. What are we doing about the problem? Dexter
Axle Company has implemented a new design with higher strength material as well as an additional weld connecting the arm to the knuckle. A remedy program has already been implemented. The service work will include: 1. Remove the existing steer arms and mounting hardware 2. Clean mounting surface and surrounding surfaces to prepare for mounting of the new bolt-on steer arm and additional welds 3. Grind a 3/16” chamfer along the mounting face edge (see page three for location & detail) 4. Mount new design steer arms (Part # 703293-LH/RH) with supplied hardware and torque to 400 ft-lbs. 5. Add welds as shown on page three of the service bulletin What should you do? Please contact a Dexter
Axle Company at 547-295-7888 at your earliest convenience to arrange an inspection, repair, or training, if required. Hyundai
Translead 8880 Rio San Diego Drive, Suite 600 San Diego CA 92108 800-251-0871 www.translead.com What if I no longer own this trailer? Notify Hyundai
Translead either by phone 866-482-2739, or e-mail [email protected] to inform us you no longer own this vehicle. Please be sure to include your 17 digit VIN number in all correspondence. Who should you contact if you have further questions or concerns? Please contact a Dexter
Axle Co. representative at 547-295-7888 and if not available contact Hyundai
Translead at 866-482-2739 or e-mail: [email protected] . If after having attempted to take advantage of this recall you believe you have not been able to have your units remedied without charge and within a reasonable amount of time, you may submit a complaint to the Administrator, National Highway Traffic Safety Administration, 1200 New Jersey Ave., S.E., Washington, D.C., 20590; or call the toll-free Vehicle Safety Hotline at 1-888-327-4236 (TTY: 1-800- 424-9153); or go to http://www.safercar.gov. Federal law requires that you forward a copy of this safety recall notice to the lessee within 10 days. We apologize for any inconvenience this safety recall may cause, however your safety is our primary concern. Sincerely, Hyundai
Translead Hyundai
Translead 8880 Rio San Diego Drive, Suite 600 San Diego CA 92108 800-251-0871 www.translead.com Istate Coxe Transp 53′ Mat. # 30017442 VIN List:
**************************************************************************************************************
**************************************************************************************************************
**************************************************************************************************************
SEOCONTENT-END
This product presentation was made with AAWP plugin.


![Steering Arm May Break - 2022 Hyundai Translead Dry Van Trailers 4 ARCCAPTAIN 165A MIG Welder 110V/220V [Large LED Display] 4 in 1 Gasless/Gas MIG/Lift TIG/Stick Welding Machine Multiprocess Welder Machine, IGBT Inverter Welder with Synergy, 2T/4T](https://m.media-amazon.com/images/I/51GW2TUAy1L._SL160_.jpg)


