July 31, 2019 NHTSA CAMPAIGN NUMBER: 19V565000
Engine May Overheat and Shutdown
If the engine unexpectedly shuts down, passengers may have to be transferred to another vehicle on the side of the road, increasing the risk of an injury. If the engine unexpectedly shuts down while the vehicle is in motion, there is an increased risk of crash.
NHTSA Campaign Number: 19V565
Manufacturer Prevost
Cars, Inc.
Components ENGINE
Potential Number of Units Affected 1,440
Summary
Prevost
Cars, Inc. (Prevost
) is recalling certain 2017-2020 X3-45 Coach, Commuter, VIP, and VIP Entertainer buses, and H3-45 Coach and VIP buses. Under certain conditions, such as high altitude and heavy climbing, the engine may overheat and shutdown.
Remedy
Prevost
will notify owners and will update the engine software, free of charge. The Prevost
issued owners an interim notification on September 27, 2019. The recall began December 19, 2019. Owners may contact Prevost
customer service at 1-866-870-2046.
Notes
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.
Prevost Technical Publications
SAFETY RECALL
SR19-31
| DATE: December 2019 | SECTION: 01 ENGINE |
| SUBJECT: | ENGINE CONTROL MODULE (ECM) SOFTWARE UPDATE – Engine Cooling Strategy in High Altitude Operation |
First Release 12-13-20
APPLICATION
|
IMPORTANT NOTICE TO SERVICE CENTERS Verify vehicle eligibility by checking warranty bulletin status with SAP or via ONLINE WARRANTY SYSTEM available on Parts and Service / Warranty tab of Prevost | |
| Model | VIN |
| X3-45 VIP motorhomes Model Year: 2017 & 2019 | 2PCBS349XHC7 2PCBS3499KC7
|
| X3-45 VIP commercial use Model Year: 2017 – 2020 | Specific vehicles within the following range
From 2PCCS3498HC73 up to 2PCCS3492LC7 incl. |
| X3-45 coaches Model Year: 2017 – 2020 | Specific vehicles within the following range
From 2PCG33491HC7 incl. From 4RKG33494J97 incl. and 2PCS33496JC7 |
| X3-45 Commuter Model Year: 2019 | 2PCJ33491KC7 |
| H3-41, H3-45 coaches Model Year: 2018 – 2020 | Specific vehicles within the following range
From 2PCH33493JC7 up to 2PCH33494LC7 incl. |
| H3-45 VIP motorhomes Model Year: 2019 – 2020 | 2PCVS3498KC
2PCVS3494KC 2PCVS3491KC7 2PCVS3497LC 2PCVS349XKC |
| This Safety Recall does not necessarily apply to all the above-mentioned vehicles, some vehicles may have been modified before delivery. The owners of the vehicles affected by this recall will be advised by a letter indicating the Vehicle Identification Number (VIN) of each vehicle concerned. | |
PART 1 – ENGINE SOFTWARE UPDATE
DESCRIPTION – PART 1
Part 1 of this safety recall applies to all the vehicles listed in the application table of the front page on which a notification identified SR19-31: PART 1- ENGINE SOFTWARE UPDATE exists.
On determined vehicles equipped with Green House Gas 17 (GHG17) or OBD18 Volvo
D13 engine, perform the latest software update of the Engine Control Module.
Please contact your nearest Prevost
Service Center or Prevost
service manager and schedule an appointment to have the required software update applied.
SOFTWARE TOOL NEEDED
Description
Latest version of Premium Tech Tool (PTT) with appropriate communication interface equipment
PROCEDURE
DANGER
Park vehicle safely, apply parking brake, stop the engine.
Lock out & Tag out (LOTO) must be performed during set-up, maintenance or repair activities. Refer to your local procedure for detailed information regarding the control of hazardous energy.
- Connect the vehicle’s battery charger to a 120-Volt outlet.
- Connect Premium Tech Tool (PTT) to the vehicle On-Board Diagnostics connector (OBD). Connect the PC to a functional LAN or Wi-Fi connection and a power source.
- Turn the ignition switch to “ON”. Activate the hazard warning flashers to prevent the vehicle from entering sleep mode.
- Log in to PTT.
- On Product tab (item A), identify the vehicle (item B).
- Select Program tab and then 1700-08-03-39 Program Electronic Control Unit. Click Start.
- Select ENGINE CONTROL MODULE (EMS).
- Select the following programming option ‘’Update Electronic Control Unit with latest software’’.
- Click Program
- Certain conditions must be met to allow programing:
- battery voltage above 10 Volts;
- parking brake applied;
- ignition key in ON position and the engine is not running.
When all conditions have been met, click Continue to proceed with programming.
- Wait until all Programming Steps check turn to green color (Programming completed).
- When the programing is complete, click Exit button.
- Clear any diagnostic trouble codes (DTC).
- Enter the Work Order Number information and then click Start Work.
WARRANTY – PART 1
Part 1 of this safety recall is covered by Prevost
’s normal warranty. We will reimburse 1/2 hour (0.5) of labor upon receipt of a warranty claim. Please submit claims via our Online Warranty System, available at www.prevostcar.com (under Service \ Warranty section). Use Claim Type: “Bulletin/Recall” and select ‘’Warranty Bulletin SR19-31”.
OTHER
| VBC Bulletin | N/A |
| Fail Code | 01.00-2 |
| Defect Code | 49 |
| Syst. Cond | R |
| Causal Part | 3092091 |
Access all our Service Bulletins on https://techpub.prevostcar.com/en/ or scan the QR-Code with your smart phone.
Are you a vehicle owner? E-mail us at technicalpublications_prev@volvo
.com and type “ADD” in the subject to receive warranty bulletins applicable to your vehicle(s) by e-mail.
PART 2 – CYLINDER LINER AND PISTON REPLACEMENT
DESCRIPTION – PART 2
PART 2 of this safety recall applies only to the vehicles listed in the application table of the front page on which a notification identified SR19-312*: PART 2- LINERS & PISTONS REPLAC exists. These vehicle mileage equals or exceeds 100 000 miles (160 000 km) at the launch of this campaign.
* SR19-312 stands for SR19-31Part2
IMPORTANT NOTICE TO SERVICE CENTERS
Verify vehicle eligibility by checking warranty bulletin status with SAP or via ONLINE WARRANTY SYSTEM available on Parts and Service / Warranty tab of Prevost
’s website.
On determined vehicles equipped with Green House Gas 17 (GHG17) or OBD18 Volvo
D13 engine, perform the replacement of the liner and piston of all six (6) cylinders.
Refer to Impact for the procedures, torque and good practice guidelines.
Suggested procedures:
ID 2171-03-02-01 Oil Pan, Replacement
ID 2131-03-03-01 Cylinder Liners and Pistons, Replacement (All)
ID 2111-03-03-03 Cylinder Head, Replacement
Other procedures found on Impact that may be useful:
2515-03-03-02 Exhaust Manifold, Replacement
2115-03-03-01 Sealing Strip, Valve Cover, Replacement
2373-08-03-04 Common Rail, Fuel Leak Test
Kit SR19-31 includes the following parts:
| # | STEP | DESCRIPTION | PART NO | QTY |
| OIL PAN | Use the following Impact procedure for reference: 2171-03-02-01 Oil Pan, Replacement | |||
| 1 | 3 | oil pan seal | 21293367 | 1 |
| 2 | gasket, magnetic plug | 20579690 | 1 | |
| LINERS & PISTONS | Use the following Impact procedure for reference: 2131-03-03-01 Cylinder Liners and Pistons, Replacement (All) | |||
| 3 | 6 | cylinder liner kit (for 6 cylinders) | 22724238
or 23775630 | 1 |
| or cylinder liner kit (for 1 cylinder) | 22565407 | 6 | ||
| 4 | 23 | bolt, piston jet | 994445 | 6 |
| 5 | 25 | fastener, stiffening frame | 969445 | 24 |
| 6 | 25 | gasket, oil pickup tube | 22275838 | 2 |
| 7 | 25 | fastener, oil pickup tube | 994451 | 3 |
| 8 | 25 | sealing ring, oil circuit, pipe on stiffening frame | 21092243 | 4 |
| CYLINDER HEAD | Use the following Impact procedure for reference: 2111-03-03-03 Cylinder Head, Replacement | |||
| 9 | 187 | gasket, cylinder head | 21510072 | 1 |
| 10 | 196 | screw, cylinder head | 21345131 | 38 |
| 11 | 209 | seal, engine brake control valve | 20526428 | 1 |
| 12 | 227 | screw, sensor wheel | 8192804 | 8 |
| 13 | 236 | O-ring, injector kit (upper grove O-ring violet) | 276948 | 6 |
| 14 | 241 | screw, injector | 21344774 | 6 |
| 15 | 268 | pressure pipe, common rail | 23000880 | 1 |
| 16 | 270 | pressure pipe, common rail right | 23000879 | 3 |
| 17 | 268 | pressure pipe, common rail left | 23000870 | 3 |
| 18 | 281 | gasket, timing gear cover | 21447682 | 1 |
| 19 | 295 | O-ring, impulse sensor cam speed sensor | 20966752 | 1 |
| 20 | 301 | pipe, Volvo | 22782247 | 1 |
| 21 | 339 | gasket, valve cover & spacer | 22777560 | 2 |
| 22 | 350 | seal, thermostat | 21503575 | 1 |
| 23 | 350 | seal, thermostat I-Shift | 975675 | 2 |
| 24 | 356 | gasket, water manifold | 21298915 | 1 |
| 25 | sealing ring, water manifold | 1547254 | 2 | |
| # | STEP | DESCRIPTION | PART NO | QTY |
| 26 | 365 | plane gasket, starter element, mixing camber | 3979639 | 2 |
| 27 | 381 | gasket, EGR valve | 20850815 | 1 |
| 28 | 381 | sealing ring, EGR valve | 20841816 | 2 |
| 29 | 383 | screw & sleeve, EGR valve | 21528673 | 4 |
| 30 | 385 | O-ring, EGR valve oil return hose | 976014 | 1 |
| 31 | 385 | seal/gasket, EGR valve oil supply hose | 976014 | 1 |
| 32 | O-ring, EGR coolant return pipe | 1547253 | 2 | |
| 33 | 389 | V-clamp, EGR valve | 20755169 | 2 |
| 34 | 392 | seal, oil return pipe | 21940615 | 1 |
| 35 | 395 | turbocharger installation kit | 85137676 | 1 |
| 36 | seal, banjo coolant turbo act supply | 947281 | 2 | |
| 37 | sealing ring, rubber (use as required) | 1547252 | 1 | |
| 38 | sealing ring, banjo fitting (use as required) | 20852765 | 2 | |
| 39 | V-clamp EGR crossover hot side | 20504408 | 2 | |
| 40 | O-ring EGR crossover hot side | 967343 | 2 | |
| 41 | V-clamp turbo to CAC pipe interface | 20592787 | 1 | |
| 42 | O-ring, V-clamp turbo to CAC pipe interface | 21096684 | 1 | |
| 43 | seal, transmission dipstick | 571662 | 1 | |
| 44 | straight coupling, EGR crossover pipe | 22889034 | 1 |
OTHER PARTS
| # | STEP | DESCRIPTION | PART NO | QTY |
| 45 | V-clamp, on Prevost | 21021850 | 3 | |
| 46 | seal ring, on Prevost | 21095726 | 3 | |
| 47 | oil filter, bypass | 21707132 | 1 | |
| 48 | oil filter, long life | 21707133 | 2 | |
| 49 | cable tie, nylon BLK (STD) | 504637 | 30 | |
| 50 | cable tie, nylon (50 POUNDS)DOUBLE LOOP | 507664 | 20 | |
| 51 | cable tie, nylon | G5007996 | 40 | |
| 52 | V-clamp, turbo outlet diffuser interface with Prevost | 21060426 | 1 | |
| 53 | gasket, turbo outlet diffuser interface with Prevost | 21095721 | 1 | |
| 54 | gasket, inlet elbow interface with mixing box | 1675066 | 1 | |
| 55 | V-clamp inlet elbow interface with mixing box | 20592783 | 1 |
NOTE
Material can be obtained through regular channels.
PART DISPOSITION
DO NOT RETURN THE REPLACED PARTS. Discard waste according to applicable environmental regulations (Municipal/State[Prov.]/ Federal)
WARRANTY – PART 2
This modification is covered by Prevost
’s normal warranty. We will reimburse you the parts and up to 50 hours of labor upon receipt of a completed A.F.A. Please submit claim via our Online Warranty System, available at www.prevostcar.com (under service \ warranty section). Use Claim Type: “Bulletin/Recall” and select ‘’Safety Recall SR19-31 “.
Should you only wish to close the safety recall (without reimbursement), fill-in the ‘’Safety Recall Certification Sheet’’ provided with this bulletin and return it to our warranty department by email at prevost
.onlinewarranty@volvo
.com or by fax at 418-831-9301.
OTHER
| VBC Bulletin | N/A |
| Fail Code | 01.00-2 |
| Defect Code | 09 |
| Syst.Cond | R |
| Causal Part | 22724238 |
Access all our Service Bulletins on https://techpub.prevostcar.com/en/ or scan the QR-Code with your smart phone.
E-mail us at technicalpublications_prev@volvo
.com and type “ADD” in the subject to receive our warranty bulletins by e-mail.
IMPORTANT SAFETY RECALL
NHTSA RECALL #19V-565
December 2019
CUSTOMER
ADD
CITY, ST ZIP
US
SAFETY DEFECT / NONCOMPLIANCE NOTICE
PREVOST
SAFETY RECALL SR19-31
Dear Customer,
This notice is sent to you in accordance with the requirements of the National Traffic and Motor Vehicle Safety Act and 49 CFR Part 573.
Prevost
Car US Inc. has decided that a defect which relates to motor vehicle safety exists on certain Prevost
vehicles as listed below.
- H3-45, model years 2018 through 2020;
- H3-45 VIP model year 2019 & 2020;
- X3-45, model years 2018 through 2020;
- X3-45 VIP Commercial Use, model years 2017 through 2020; X3-45 VIP Private Use, model years 2017 & 2019.
According to our records, you are the registered owner of the following vehicles involved in safety recall SR19-31 PART 1 “Engine Control Module (ECM) Software Update”:
VIN
DEFECT DESCRIPTION
Under certain high-altitude and heavy load conditions, the engine could overheat.
FAILURE CONSEQUENCE
This could cause a disabled vehicle. Disabled vehicle may lead to transferring passengers on the side of the road, which may increase the risk of a passenger death or injury. Prevost
has not received report of death or injury associated with this defect. Therefore, we consider this as a proactive measure to protect the public from the potential risk associated with this defect.
WHAT YOU NEED TO DO
Please make an appointment to your nearest Prevost
Service Center and refer to PART 1 of SR19-31 to receive an engine software update that will improve the cooling system strategy. This update is available and can already be uploaded into your vehicle.
Optionally, you may have the work performed by qualified personnel of your choice, following PART 1 of Safety Recall SR19-31 available on Prevost Technical Publications web site at this address: https://techpub.prevostcar.com/en/
Prevost
will reimburse you the labor as described in the SR19-31 procedure. Please file an online warranty claim following normal campaign procedures if you are a registered customer, otherwise, contact the Prevost
Warranty Department at 1-866870-2046 for reimbursement instructions.
The time required to perform the software update on your vehicle is ½ hour (0.5 h).
OTHER REPAIR – PART 2 OF SAFETY RECALL SR19-31
PART 2 of safety recall SR19-31 applies to the vehicles having a mileage greater than 100 000 miles (160 000 km) at the launch of this campaign. In addition to the engine software update covered by PART 1 of SR19-31, the replacement of the cylinder liners and pistons will be carried out on these vehicles, free of charge.
If applicable, you will find the list of vehicles involved in SR19-31 PART 2 “Cylinder Liners & Pistons Replacement” appended to this notice letter.
The estimated time required to perform PART 2 of this campaign is 50 hours.
The parts required to perform SR19-31 PART 2 will be available from mid-February 2020. Please make an appointment to your nearest Prevost
Service Center from midFebruary to have the hardware replacement performed on your vehicle.
NOTICE REGARDING LEASED VEHICLES
If you are a vehicle lessor, Federal Law requires that any vehicle lessor receiving this recall notice must forward a copy of this notice to the lessee within ten working days.
CHANGE OF ADDRESS OR OWNERSHIP
If your address has changed, or you no longer own the vehicle(s), please help us update our records. Accessing the Prevost
Warranty Support web page https://www.prevostcar.com/parts-and-services/warranty , fill-in the form ‘Change of address or ownership’, and email it to prevost
.onlinewarranty@volvo
.com.
ASSISTANCE
If you need assistance, please contact your nearest Prevost
Service Center. You will find the Prevost
Parts & Service Centers location at this address: https://www.prevostcar.com/contact-us/prevost-service-centers
COMPLAINTS
If you believe that Prevost
Car US has failed or is unable to remedy the defect within a reasonable time, you may submit a complaint to the Administrator, National Highway Traffic Safety Administration, 1200 New Jersey Avenue S.E., Washington, D.C. 20590, or call the toll-free Vehicle Safety Hot Line at 1-888-327-4236 (TTY: 1800-424-9153), or go to https://www.safercar.gov.
We regret any inconvenience this may cause to your operation, but hope you will appreciate our sincere efforts to demonstrate Prevost
’s commitment to provide our customers with the best possible product.
Truly yours,
Prevost
Service Team
CUSTOMER
ADDRESS BLOCK
APPENDIX
List of vehicles involved in SR19-31 PART 2 “Cylinder Liners & Pistons Replacement”
PART 2 of safety recall SR19-31 applies to the vehicles having a mileage greater than 100 000 miles (160 000 km) at the launch of this campaign.
According to our records, you are the registered owner of the following vehicles involved in PART 2 of safety recall SR19-31:
VIN XXXXXX Miles
IMPORTANT SAFETY RECALL
NHTSA RECALL #19V-565 September 2019
INTERIM NOTICE
We are currently preparing the remedy. We will notify you again when the remedy is ready.
«customer»
«add» «po»
«city», «st» «zip»
«pays»
SAFETY DEFECT / NONCOMPLIANCE INTERIM NOTICE
PREVOST SAFETY RECALL SR19-31
Dear Customer,
This interim notice is sent to you in accordance with the requirements of the National Traffic and Motor Vehicle Safety Act and 49 CFR Part 573.
Prevost
Car US Inc. has decided that a defect which relates to motor vehicle safety exists on certain Prevost
vehicles as listed below.
- H3-45, model years 2018 through 2020;
- H3-45 VIP model year 2019;
- X3-45, model years 2018 through 2020;
- X3-45 VIP Commercial Use, model years 2017 through 2019;
- X3-45 VIP Private Use, model years 2017 & 2019.
According to our records, you are the registered owner of the following vehicles involved in safety recall SR19-31:
DEFECT DESCRIPTION
Under certain high-altitude and heavy load conditions, the engine could overheat.
FAILURE CONSEQUENCE
This could cause a disabled vehicle. Disabled vehicle may lead to transferring passengers on the side of the road, which may increase the risk of a passenger death or injury. Prevost
has not received report of death or injury associated with this defect. Therefore, we consider this as a proactive measure to protect the public from the potential risk associated with this defect.
WHAT YOU NEED TO DO
We appreciate your patience while we are preparing the remedy. You will receive a second owner notification when the solution is available. There may be warnings or indicators that this condition exists. These warnings will typically be due to fault codes triggered for engine coolant over temperature condition or engine coolant level low.
NOTICE REGARDING LEASED VEHICLES
If you are a vehicle lessor, Federal Law requires that any vehicle lessor receiving this recall notice must forward a copy of this notice to the lessee within ten days.
CHANGE OF ADDRESS OR OWNERSHIP
If your address has changed, or you no longer own the vehicle(s), please help us update our records. Accessing the Prevost
Warranty Support web page https://www.prevostcar.com/parts-and-services/warranty , fill-in the form ‘Change of address or ownership’, and email it to prevost
.onlinewarranty@volvo
.com.
ASSISTANCE
If you need assistance, please contact your nearest Prevost
Service Center. You will find the Prevost
Parts & Service Centers location at this address: https://www.prevostcar.com/contact-us/prevost-service-centers
COMPLAINTS
If you believe that Prevost
Car US has failed or is unable to remedy the defect within a reasonable time, you may submit a complaint to the Administrator, National Highway Traffic Safety Administration, 1200 New Jersey Avenue S.E., Washington, D.C. 20590, or call the toll-free Vehicle Safety Hot Line at 1-888-327-4236 (TTY: 1800-424-9153), or go to https://www.safercar.gov.
We regret any inconvenience this may cause to your operation, but hope you will appreciate our sincere efforts to demonstrate Prevost
’s commitment to provide our customers with the best possible product.
Truly yours,
Prevost
Service Team
8 Affected Products
Vehicles
8 Associated Documents
Recall Quarterly Report #1, 2019-4
RCLQRT-19V565-7928.PDF 211.127KB
Recall Quarterly Report #2, 2020-1
RCLQRT-19V565-2824.PDF 211.232KB
Recall Acknowledgement
RCAK-19V565-2178.pdf 244.928KB
Defect Notice 573 Report
RCLRPT-19V565-5391.PDF 213.645KB
ISSUED Interim Owner Notification Letter(Part 577)
RIONL-19V565-4672.pdf 207.882KB
Recall 573 Report- Amendment 4
RCLRPT-19V565-1359.PDF 213.655KB
Remedy Instructions and TSB
RCRIT-19V565-8812.pdf 616.566KB
ISSUED Owner Notification Letter(Part 577)
RCONL-19V565-3443.pdf 749.285KB
Latest Recalls Documents
Heavy Duty Truck Reprogramming
Description:
Designed for flexibility, the USB-Link 3 Wired Edition connects to your PC, tablet, or smartphone with a USB cable, allowing techs to directly connect to a device when working in the field or during signal interruptions.
Built to support the latest protocols (CAN FD, DoIP) and compatible with a wide range of OEM diagnostics software, the USB-Link 3 is our most advanced VCI to date, with the performance and technology you can rely on well into the future.
The USB-Link™ 3 comes with the following:
- Latching USB Cable (PN 404032)
- 9-Pin Deutsch Adapter, 1 Meter (PN 493128)
- J1962 Adapter (16-Pin OBD II, 1 Meter (PN 491113)
The USB-Link™ 3: Wireless is also available (PN 121052).
Specifications
Vehicle Network Protocol Support
CAN FD / J1939 FD / ISO15765 FD - 250K, 500K, 1M b/s with auto baud detection
Single wire CAN (SWCAN)
ISO 11898-3 Fault Tolerant CAN (FTCAN)
Diagnostics Over Internet Protocol (DoIP)
J1708
J1850 VPW (Class 2)
ISO PWM (SCP)
ISO 9141 / KWP2000 (ISO 14230) K/L line
ALDL 9600 and 8192 baud
ATEC 160 baud
Windows® Vehicle Communication API
Windows® Vehicle Communication API
RP1210 a/b/c
J2534 (2004 draft)
J2534-1 partial implementation (commercial vehicle focused)
Operating System Compatibility
iOS
Android™
Windows® 10, 11
Interfaces to Computing Platforms
USB 2.0 (vehicle-to-PC connectivity)
Bluetooth® 2.1 + EDR
Wi-Fi (dual band)
Compatible Software
Detroit Diesel Diagnostic Link
CAT Electronic Technician (On-Highway only)
Cummins
Insite
International
- ServiceMAXX Fleet Pro
Hino eXplorer
Volvo
PTT
VCAD Elite Mack
/Volvo![]()
V-MAC Service Tools
Allison DOC® For PC-Service Tool - Protocols Supported: J1939, J1708/J1587, and J1850
Allison DOC® For Fleets (1000/2000) - Protocols Supported: J1939, J1850
Allison DOC® For Fleets (3000/4000) - Protocols Supported: J1939, J1708/J1587
Eaton
ServiceRanger
Bendix
ACom
WABCO Toolbox
Freightliner
ServiceLink
International
ABS
International
DLB
International
Intune
International
IPC v2.02
PACCAR
DAVIE4
Daimler Truck
DiagnosticLink Order Site:
DiagnosticLink Direct Link:
https://diagnosticlink.nexiq.com/DTNA/Default.aspx
- 【Built for Heavy Duty Diesel Diagnostics】Designed for SAE J1939 and J1708 compliant trucks, buses, and diesel-powered commercial vehicles. HD601 truck scanner diagnostic tool helps owner-operators, small fleets, mobile technicians, and independent repair shops quickly identify fault codes, view live data, and make informed repair decisions—saving time, reducing downtime, and avoiding unnecessary shop visits
- 【Full System Diagnostics+All HD OBD Modes】The New HD601 heavy duty truck scanner delivers full-system diagnostics on SAE J1939 and J1708-compliant commercial vehicles—digging into engine, transmission, ABS, fuel, every system that keeps your rig rolling. It supports all HD OBD modes, giving you live data, freeze frame, ECU info, vehicle info, emissions data tracking, plus code reading and clearing. Not just what broke, but why—so you fix it right the first time. Pinpoint issues faster, cut repair costs, and spend less time on the shoulder
- 【Wide Heavy-Duty Vehicle Coverage】Supports a wide range of heavy-duty vehicle manufacturers and systems, including Freightliner
, Kenworth
, Peterbilt
, Volvo
, International
, Detroit, Cummins
, Paccar
, Allison, Eaton
, Bendix
, Wabco, and more. Coverage varies by vehicle make, model, year, and system configuration. Contact our support team before purchase if compatibility verification is needed - 【Speaks Major Truck Protocol】The New HD601 diesel truck scanner is built for American-made trucks—and supports the heavy‑duty protocols you' re most likely to run into on the road: SAE J1939, J1708/J1587, ISO 15765‑4, ISO 14230‑4, ISO 9141‑2, J1850 PWM/VPW, ISO 27145‑4, and EURO‑6. For most trucks, model years, and systems, it speaks the language your vehicle understands. Just plug it in and start diagnosing—no guesswork, no gatekeeping. Note: vehicle functions and module availability may vary by manufacturer and model year
- 【Save Hundreds on Diagnostic Fees】Why pay $150–300 for someone to read your codes? With the New ANCEL heavy duty truck scanner, you can pull fault codes yourself—in minutes, without leaving the truck. One or two uses pays for the tool. After that, every diagnostic is money back in your pocket. Smart investment for owner-operators, techs, and small fleets. Read and clear stored fault codes in minutes. Active fault codes may require repairs before they can be cleared
- ALL-IN-ONE HEAVY-DUTY DIAGNOSTIC PLATFORM FOR PROFESSIONAL WORK – ANCEL X7HD PRO diesel scanner combines full-system diagnostics, HDOBD/OBD2 coverage, 42+ reset functions, bi-directional control, and ECU coding in one integrated platform. Designed for diesel technicians and fleet maintenance, it reduces tool switching and helps complete complex truck diagnostics faster, more accurately, and with greater efficiency in real repair environments
- 42+ SERVICE & RESET FUNCTIONS FOR DAILY MAINTENANCE JOBS – Perform a wide range of essential service tasks including DPF regeneration, injector coding, oil reset, throttle adaptation, EPB reset, ABS bleeding, and idle/speed adjustment. Built for real workshop needs, this diesel scan tool helps reduce dealership visits, expand service capabilities, and handle more maintenance jobs with a single scanner
- ADVANCED BI-DIRECTIONAL CONTROL & ACTIVE TESTING CAPABILITY – Send direct commands to vehicle components such as fuel injectors, ABS systems, cooling fans, and throttle actuators. Monitor real-time responses to verify system behavior before replacing parts. The truck scanner reduces unnecessary disassembly, improves fault pinpointing accuracy, and significantly shortens overall diagnostic and repair time
- ECU CODING & MODULE MATCHING FOR POST-REPAIR CALIBRATION – Support ECU coding and module matching for component replacement, system adaptation, and factory recalibration after repairs. Helps ensure proper communication between newly installed parts and existing vehicle systems, reducing compatibility issues and improving long-term reliability in complex diesel truck platforms
- FULL-SYSTEM HDOBD/OBD2 DIAGNOSTICS WITH WIDE COVERAGE – Read and clear codes, view live data, freeze frame, and monitor key systems including engine, transmission, ABS, and body. Compatible with Freightliner
, Kenworth
, Peterbilt
, Volvo
, Mack
, International
, plus Cummins
, Caterpillar
, Detroit, Paccar
, Navistar
engines, and standard OBD2/EOBD vehicles, suitable for mixed fleets and workshops
- 【One Tool, Total Fleet Coverage: 6/9/16 Pin Ready】Featuring an integrated 16-pin OBD2 connector and professional-grade 6-pin & 9-pin adapters, this heavy duty truck scanner provides extensive support for J1939, J1708, J1587, ISO 14230-4, ISO 15765-4 and ISO 9141-2, ISO 27145-4 protocols. It offers reliable diagnostic coverage for major American diesel brands—including Cummins
, Paccar
, Caterpillar
, Detroit, and Freightliner
—making it a versatile semi truck scanner for managing any diverse fleet. - 【2 in 1 Diesel Code Reader & Advanced HD OBDII】Equipped with professional-grade diesel scanner capabilities, the HD301 diesel scanner features intuitive Read/Erase codes and turn off the "Check Engine" light. With the built-in DTC Lookup library, you can instantly access fault code definitions on-device without searching the internet. It also retrieves hundreds of essential live sensor data—such as coolant temperature, fuel pressure, and engine RPM—in a stable text format for precise and rapid troubleshooting. (Please note that the HD301 can not support DPF Regen.)
- 【Full System Truck Diagnostic】The FOXWELL HD301 heavy duty scan tool is engineered to deeply access and scan all available electronic control modules specifically for truck, including Engine, Transmission, ABS, SRS, Chassis, and Body Control. This professional truck scanner diagnostic tool allows you to identify issues across the entire vehicle, ensuring your rig stays in peak condition for the long haul.
- 【Versatile for most big Rigs: Commercial, Passenger & Beyond】Engineered for more than just trucks, this heavy duty scan tool offers extensive coverage for pickups, buses, trailers, and even marine vessels. From construction machinery (excavators, loaders) to agricultural equipment (tractors, harvesters), it provides a true all-in-one diagnostic solution.
- 【Plug-and-Play & No Subscription】Designed for the road! No WiFi, no batteries, and no complex App setup required. Simply plug it into your vehicle’s diagnostic port to start scanning immediately. Enjoy lifetime free software updates to keep your HD301 diesel truck scanner current with the latest vehicle models and features—without any hidden subscription fees—While overcoming language barriers with support for Spanish and English.
- Complete Heavy-Duty Truck Diagnostics — ANCEL X7HD combines 40+ reset functions, bi-directional control, ECU coding, full-system diagnostics, and complete HDOBD/OBD2 coverage in one professional diesel scan tool. Built with a 10.1" tablet, Android system, 6000mAh battery, Bluetooth, Wi-Fi, live data graphing, report printing, 14 languages, remote support, and 2 years of free updates, it helps shops and fleet teams handle real truck diagnostics more efficiently
- 40+ Service & Reset Functions — Cover more maintenance jobs with 40+ reset and service functions, including DPF regeneration, oil reset, injector coding, ECU reset, speed and idle adjustment, EPB, ABS, SRS, suspension calibration, throttle reset, and more. Designed for daily diesel repair work, X7HD helps technicians complete more service tasks without switching between multiple diagnostic tools
- Bi-Directional Control & Active Tests — Go beyond basic code reading by sending commands to vehicle systems and actively testing components such as injectors, ABS, throttle, and other supported modules. Bi-directional control helps technicians verify component response, locate faults faster, reduce unnecessary disassembly, and confirm repairs with greater confidence
- ECU Coding & Module Matching — Perform ECU coding and module matching to adapt new components, restore factory settings, and resolve system mismatches after repairs. This function is useful for injector replacement, module updates, calibration work, and fleet maintenance, helping supported systems communicate correctly after service or component replacement
- Full-System Diagnostics + HDOBD/OBD2 Coverage — Scan major truck systems including engine, transmission, ABS, body, chassis, and more, while also supporting HDOBD, OBD2, and EOBD functions for broader vehicle coverage. Read and clear codes, view live data, check freeze frame, and monitor system status in real time, making it suitable for both heavy-duty trucks and standard vehicles
- Built for Heavy-Duty Trucks in Commercial Service: Go beyond basic passenger-car code reading with a heavy duty truck scanner built for real diesel truck service. Helps owner-operators, fleets, repair shops, used-truck businesses, and logistics teams handle everyday truck maintenance, prepare for DPF service, and troubleshoot with more confidence
- Get Back on the Road Faster with DPF Regen & Reset: Help perform DPF forced regeneration and DPF reset on supported Cummins
, PACCAR, Caterpillar
, Detroit, HD Volvo
, Mack, International
, and MaxxForce applications. Built-in CAN3 channel access helps complete regen and basic diagnostics without an extra CAN-3 adapter, so you can address soot-related issues sooner and reduce aftertreatment downtime - Wide Coverage for Daily Service Needs: Works with Diesel OBD and OBD2 systems across Freightliner
, Peterbilt
, Kenworth
, HD Volvo
, Mack, International
, Western Star
, and more. Read vehicle information, clear fault codes, view live data, and perform oil reset on supported Isuzu
, Fuso, and Hino applications—helping fleets and shops complete routine checks faster with fewer workflow delays - Smarter Tools for Faster, More Reliable Repairs: Topology display, wiring diagrams, Pin Detect, and Pre/Post scan reports help technicians visualize system relationships, locate wiring or connector issues, document faults before service, and verify repairs after service. Clear reports help reduce guesswork, avoid rework, and support customer, fleet, and insurance claim documentation
- Free Software Updates, No Annual Fees: Get free software updates for the life of the device, which may help you save hundreds of dollars compared with subscription-based scanners. One-click software updates help keep your scanner current without extra annual fees, giving fleets, repair shops, and owner-operators better long-term value
- Diagnose Heavy-Duty Truck Problems Fast — Read and clear fault codes and diagnose warning light issues on many Class 4–8 diesel trucks including Freightliner, Peterbilt, Kenworth, Volvo
, Mack and Cummins-powered vehicles - Help Reduce Downtime & Repair Costs — It offers full system diagnostics for major trucks meeting standard protocols, along with complete OBD2 functionality. Quickly check engine faults, view live truck data and identify issues before expensive repair shop visits or unnecessary repairs
- No complicated setup required — Simple menus and built-in DTC explanations make this truck code reader easy to use for owner-operators, mobile mechanics and small fleet maintenance
- Live Data & Built-in DTC Lookup — View real-time engine data and built-in truck fault code definitions directly on the scanner to help understand vehicle problems faster without searching through manuals
- Free Lifetime Updates & Technical Support — Includes free software updates plus responsive technical support for setup, compatibility and everyday truck diagnostics
This product presentation was made with AAWP plugin.





