Ride Height – Clearance Increase – 2018 Highland Ridge Ultra Lite

SEOCONTENT-START

PIN 19-001 – Ride Height – Clearance Increase May 2019 Page 1 of 4
Ride Height – Clearance Increase
Incident:
Complaints of rear of unit being too low
Affected Units:
Highland Ridge Fifth Wheels
Parts Kit: P004-17JT
Parts Kit #: P004-17JT
Contents:
 2 – Washer, Lk Split .50 ZC, Grade 8
 2 – Hex Nut .50-13 ZC, Grade 8
 1 – Bolt, Hgr Grs .56 X2.90 Shlder, .44-20 THD
 1 – HGR Bolt .44-20 Flg-Top LK
 1 – Hanger, Spr Ext LH
 1 – Hanger, Spr Ext RH
 2 – Hex Bolt, .50-13X4.00 ZC, Grade 8
 1 – Tubing, DOM Astma513, Type 5, 0.75” ODX0.50”IDXX1.90”
Misc. Tools & Supplies:
o Drill and a 1/2″ drill bit
o Torque wrench
o Ratchet wrench with ¾” socket
o Welder
o Spray paint
Parts Return Information:
N/A
Bulletin Type:
PIN
Bulletin #(s):
19-001
Job Code(s):
N/A
Flat Rate(s):
N/A
Publication Date:
May 2019
Make(s):
Highland Ridge
Model(s):
Ultra Lite
Model Year(s):
2018
PIN 19-001 – Ride Height – Clearance Increase May 2019 Page 2 of 4
INSTRUCTIONS
STEP 1:
Position the lift plates to install onto the spring
hanger. Insert the steel bolt sleeve into the hanger to
align with the bolt hole.
STEP 2:
Install the first bolt, a 4” x ½”– 13 grade 8 hex bolt
into lift plates and the hanger hole passing through
the steel sleeve.
STEP 3:
Install the lock washer and hex nut. Torque the nut
to 90 ft.-lbs.
PIN 19-001 – Ride Height – Clearance Increase May 2019 Page 3 of 4
¼”
¼”
STEP 4:
Using a 1/2″ drill bit, drill for a second ½” bolt using
the upper plate hole as the location and guide.
Install the bolt and secure as previously described in
STEP 3.
STEP 5A:
Weld the assembly as shown and indicated by the
GREEN weld lines. This view is from the exterior of
the vehicle.
STEP 5B:
Weld the assembly as shown and indicated by the
GREEN weld lines. This view is from the underside of
the vehicle.
PIN 19-001 – Ride Height – Clearance Increase May 2019 Page 4 of 4
¼”
¼”
Jayco’s sole obligation under our limited warranty is to repair or replace defective materials and/or workmanship deemed our responsibility as determined
by Jayco in our sole discretion. Jayco reserves the right to use new and/or remanufactured parts or materials of similar quality to complete any work, and to
make parts and/or design changes as appropriate without notice to anyone. Jayco designs and/or materials changes are done without obligation to
incorporate such changes in previously manufactured product. Jayco makes every reasonable effort to ensure field remedies will not adversely affect
performance and/or safety of the unit. This field remedy is not intended to extend to future performance of this RV, or any of its materials, components or
parts beyond the standard warranty period. The RV owner’s obligation to notify Jayco, or one of its independent, authorized dealers, of a claimed defect
does not modify any obligation placed on the RV owner to contact Jayco directly when attempting to pursue remedies under state or federal law. Jan. 2019.
903 South Main Street • P.O. Box 460 • Middlebury, IN 46540
STEP 6:
All of the previous details show a cross tube that
runs from one side of the vehicle to the other
connecting the 2 x 2 or 2 x 3 -spacer tube. These
are found on the front and rear hangers on some
models. Middle hangers on these units will not have
the cross tubes. This view shows the welding for
applications where there is not a cross tube used.
NOTE:
The cross channel shown in the diagrams is used on
some units and not others. Therefore the
instructions are the same regardless of the presence
of a cross channel.
STEP 7:
After welding is complete:
 Remove weld slag.
 Touch-up weld affected zones with a good paint/rust inhibitor.