Wheel Fender Stainless Steel Protector – 2011-2019 Prevost

SEOCONTENT-START

Writer: FL <QF7720959 rev 5>
Instruction Sheet IS-17900A
WHEEL FENDER STAINLESS STEEL PROTECTOR
H SERIES VEHICLES – B-1721- Today
REVISION:A This revision replaces all previous versions
2017-04-07 Changed vehicle effectivity. Was 2004.
MATERIAL
Kit #7770321 includes the following parts:
Part No. Description Qty
470933 FENDER PROTECTOR 8
506869 TAPE RUB ADH2 POL .031″ x 1/4″ x 300′ / BLACK 1
684517 ADHESIVE SIMSON #ISR 70-03 / GREY / 310ml CARTRIDGE 1
504643 RIVET POP DOME OE 1/8x.640 SS 40
5001067 WASHER FL .128x.312x.032 SS 40
IS-17900 Instruction Sheet 1
FI-17900 Feuille d’instructions 1
NOTE
Material can be obtained through regular channels.
Other parts that may be required:
Part No. Description Qty
682986 STANDOX Anti-Silicone cleaning fluid, 4 liter 1
PROCEDURE
DANGER
Park vehicle safely, apply parking brake, stop engine. Prior to working on the vehicle, set the ignition
switch to the OFF position and trip the main circuit breakers equipped with a trip button. On Commuter
type vehicles, set the battery master switch (master cut-out) to the OFF position.
IS-17900A
Page 2 / 5
Writer: FL <QF7720959 rev 5>
GLUING – BEST PRACTICES
Health & Safety
DISCARD
WASTE PROPERLY
WEAR
GLOVES
WEAR
SAFETY GLASSES
Work environment
– Free from excessive dust (ensure ventilation).
– Air jet prohibited. (Propels dust into the working environment and causes surface contamination from the
oil of the pneumatic system).
– All products containing silicone are prohibited.
Temperature and % humidity: The standard is established at 23 oC (73°F) and 50% relative humidity.
Effect of temperature;
> 23 oC and/or > 50%, drying time and working time are reduced
< 23 oC and/or < 50%, drying time and working time are increased
On the other hand, usage of products, parts, surface preparation and/or bonding is not allowed below
15oC.
General information for cleaning / surface preparation products
Do not
rub back and forth
Check the expiry date Do not pour
directly from the bottle
IS-17900A
Page 3 / 5
Writer: FL <QF7720959 rev 5>
NOTE
The kit includes the required material to install 8 stainless steel fender protectors on a vehicle.
FIGURE 1 PROTECTOR LOCATIONS
1. Water-clean the fender’s lower
edge. Clean the inner and outer
faces thoroughly, removing any
dirt, salt, sand or road material.
Dry the surface.
2. Next, clean the protector,
removing any dust or residue.
3. Once dry, use anti-silicone to
prepare the fender and
protector surfaces for bonding.
FIGURE 2 :CLEAN THESE AREAS ON FENDER
IS-17900A
Page 4 / 5
Writer: FL <QF7720959 rev 5>
4. Select a glue applicator nozzle
that creates 8mm high glue
beads. (Figure 3)
5. If unavailable, cut an 8mm high
triangular opening in the tip.
(Figure 3)
FIGURE 3 TRIANGULAR BEAD OF GLUE
6. Perform a dry fit of the protector
on the fender. Mark tape
positions with masking tape
according to Figure 4.
7. Prepare two 14-1/4” lengths of
double-face tape.
8. Immediately position the tapes
on the fender.
9. Apply a bead of Simson glue
between the tapes Figure 4.
FIGURE 4 : TAPE PLACEMENT UNDER PROTECTOR.
IS-17900A
Page 5 / 5
Writer: FL <QF7720959 rev 5>
10. Within 10 minutes of glue
application, place protector
against inner face of fender
(1, Figure 5 ). Then, push
against outer face (2, Figure 5 ).
FIGURE 5 INSTALLATION SEQUENECE
11. Using the protector as a
template, drill 1/8” holes for
rivets. (5x)
12. Install the rivets.
FIGURE 6
13. Full curing time: 9 1/2h @ 73°F (23°C), 50% Relative Humidity.
Curing time may be shorter or longer depending on temperature and humidity.
PARTS / WASTE DISPOSAL
Discard waste according to applicable environmental regulations (Municipal/State[Prov.]/ Federal)