Footrest May Fall off – 2020 Moto Guzzi V85 TT Motorcycles

December 3, 2019 NHTSA CAMPAIGN NUMBER: 19V858000

Footrest May Fall off

A footrest that falls off while the motorcycle is in motion may become a road hazard, increasing the risk of a crash.

 

NHTSA Campaign Number: 19V858

Manufacturer PiaggioeBay logo Group Americas. Inc.

Components EQUIPMENT

Potential Number of Units Affected 399

 

Summary

PiaggioeBay logo Group Americas. Inc. (PiaggioeBay logo) is recalling certain 2020 Moto GuzzieBay logo V 85 TT motorcycles. The footrest mounting pin retaining clip may break, allowing the pin to disconnect and the footrest to fall off the motorcycle.

 

Remedy

PiaggioeBay logo will notify owners, and dealers will inspect the retaining rings on all four footrests. If any of the clips are found to be defective, the dealer will replace the retaining clips on all four footrest pins, free of charge. The recall began December 26, 2019. Owners may contact PiaggioeBay logo customer service at 1-212-380-4433. PiaggioeBay logo’s number for this recall is PGJZZQ1905.

 

Notes

Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.

 


Date: December 26, 2019

Dear Valued Customer:

 

IMPORTANT  SAFETY  RECALLS

Regarding your:  2020 Moto GuzzieBay logo V85TT

THIS NOTICE APPLIES TO YOUR VEHICLE    VIN:                                                   

NHTSA Recall #’s 19V-857/19V-858

 

This notice is sent to you in accordance with the requirements of the National Traffic and Motor Vehicle Safety Act. The internal campaign codes for Recalls 19V-857 and 19V-858 are PGJZZQ1904 and PGJZZQ1905 respectively.

 

REASON FOR THIS RECALL 

Moto GuzzieBay logo USA has decided that defects, which relate to motor vehicle safety, exist in a specific range of Moto GuzzieBay logo motorcycles noted below:

  • MY 2020 V85TT models

 

In the affected range, Moto GuzzieBay logo USA has found that the final drive may develop a leak, leaking oil onto the rear tire (Recall 19V-857). This oil leak on the rear tire may cause a loss of vehicle control or a crash, increasing the risk of injury

It has also been discovered that the retaining clips for the footrest pins may not be adequately secured, which could cause the footrest to detach and fall from the vehicle (Recall 19V-858). If the footrest falls off, it may cause a loss of vehicle control or a crash, increasing the risk of injury.  According to vehicle registration records, you are the owner of a vehicle that falls within this affected VIN range.

 

WHAT WE WILL DO 

To address this situation, Moto GuzzieBay logo USA will conduct the recalls for the vehicles within the affected VIN range. Moto GuzzieBay logo USA, through the qualified dealer network, will inspect the final drive unit for oil leakage.  If no leakage is found, an outer seal/cover will be installed in the final drive hub to prevent oil leakage on the wheel/tire assembly.   If leakage is found during the inspection, a replacement of a set of internal seals will be performed under warranty first and then the outer seal/cover will be installed to fulfill the recall. Concerning the footrest pin retaining clips, all four clips will be inspected for proper fitment.  If one or more clips are found to be defective, all four clips will be replaced under the recall. This repair campaign will eliminate any potential safety risk.   

In addition to the two recalls being performed, there are additional technical updates that will be completed at no charge that are not classified as safety related. Depending on your particular VIN, these updates may include installing a new clutch cable guide arch, tightening the oil sump screws and sump guard fasteners, installing locking nuts on the lumbar support cushion or inspecting rear brake master cylinder for fluid seepage.

Considering the inconvenience this has caused, a general inspection of your vehicle will also be performed free of charge.  This inspection will cover the front and rear suspension, brake pads, lighting system and safety switches. In addition, a comprehensive check of all control modules will be performed using the Moto GuzzieBay logo diagnostic tool.

The technical updates and general inspection are free optional services, and not required as part of the two safety recalls.

The work required by this recall may be completed by your qualified Moto GuzzieBay logo dealer at no charge to you for the required parts and labor. The work time to install the final drive seal/cover is approximately 20 minutes (an additional 100 minutes is necessary if a final drive leak is found).  The footrest pin retaining clip inspection will require 5 minutes if all clips are compliant and 10 minutes for non-compliance (all four clips replaced).  The free general vehicle inspection will require approximately 20 minutes.

 

WHAT YOU SHOULD DO

With the receipt of this letter, please contact your authorized Moto GuzzieBay logo dealership as soon as possible to schedule an appointment to have the recalls and technical updates completed. Instructions for this recall have been sent to your dealer and the parts are available. Your dealer is best equipped to obtain parts and provide service to ensure that your vehicle is corrected as promptly as possible. Please ensure that these instructions are followed by anyone that uses your vehicle.

If you take your vehicle to your dealer on the agreed service date and they do not remedy this condition on that date or within three (3) days, we recommend you contact our Customer Care helpline at 212-380-4433.

After contacting your dealer and the above number, if you are still not able to have the safety defect remedied without charge and within a reasonable time, you may wish to write to: The Administrator, National Highway Traffic Safety Administration, 1200 New Jersey Ave SE, Washington, DC 20590, or call the toll-free Vehicle Safety Hotline at 1-888-327-4236 (TTY: 1800-424-9153); or go to https://www.safercar.gov.

Our Customer Care helpline (212-380-4433) is available to provide you with further information and any support you may need. Should the vehicle not be in your possession or available to you, please provide the name and address of the purchaser by contacting our Customer Care  department or by filling out the form on the following page. This form can be faxed to 212-3804459. Our Customer care email is: [email protected]

If you previously had the work required of this recall completed at your own expense, please refer to the attached letter (Tread Act Customer Reimbursement Plan) describing the criteria and procedure to request reimbursement.

Federal law requires any lessor who receives a notification of a determination of a safety-related defect or noncompliance pertaining to any leased motor vehicle shall send the notice to the lessee within 10 days.

We are sorry to cause this inconvenience; however, we have taken this action in the interest of your safety and continued satisfaction with our products. Thank you for your prompt attention to this important matter.

 

Very truly yours,

 

Moto GuzzieBay logo USA- Technical Services  PiaggioeBay logo Group Americas

 


TREAD ACT CUSTOMER REIMBURSEMENT PLAN 

 

Customer Reimbursement for Safety Related Recall Repairs

Effective with Safety related recalls initiated as of January 15, 2003

 

Moto GuzzieBay logo USA is initiating a safety related recall for a select range of models that includes your VIN number. If you have previously paid to have the repair or update as described in the recall documentation completed, you are entitled to be reimbursed for that expense.

You are encouraged to request reimbursement from your respective Moto GuzzieBay logo dealer.  Alternatively, you may submit the request for reimbursement to the following address:

Customer Care
Moto GuzzieBay logo USA
1020 W. 17th Street
Costa Mesa, CA 92627

 

In every case:

  • Repair expenses pertaining to the subject of the safety recall are reimbursable, not consequential expenses such as towing, rental, accommodations, damage repairs, etc.
  • Expenses from repair facilities outside of the Moto GuzzieBay logo USA authorized dealer network will be considered; however, the repair procedure must meet Moto GuzzieBay logo USA’s standards.
  • When reimbursing for parts, the Manufacturers Suggested Retail Price (MSRP) will be considered as the guideline for reasonable charges.
  • Expenses for repairs performed more than 10 days after the date of the last customer notification letter sent by Moto GuzzieBay logo USA are not eligible for reimbursement.
  • Taxes and hazardous waste disposal, where previously paid, are eligible for reimbursement.

The authorized  Moto GuzzieBay logo  dealer will request a copy of the customer notification letter, as well as a copy of the owner’s previously paid invoice, and then inspect the vehicle (if still in the possession of the invoice holder) to determine the scope and quality of the previous repair.  Claims will be processed within 60 days of receipt.

 


1 Affected Product

Vehicle

MAKEMODELYEAR
MOTO GUZZIeBay logoV85 TT2020

 


8 Associated Documents

ISSUED Owner Notification Letter(Part 577)

RCONL-19V858-8262.pdf 53.565KB

 


Recall Quarterly Report #3, 2020-2

RCLQRT-19V858-4808.PDF 211.326KB

 


Recall Quarterly Report #1, 2019-4

RCLQRT-19V858-1347.PDF 211.138KB

 


Recall Quarterly Report #2, 2020-1

RCLQRT-19V858-1199.PDF 211.241KB

 


Defect Notice 573 Report

RCLRPT-19V858-4587.PDF 214.363KB

 


Recall Acknowledgement

RCAK-19V858-7250.pdf 245.679KB

 


Recall 573 Report – Amendment 1

RCLRPT-19V858-9561.PDF 214.501KB

 


Recall Quarterly Report #4, 2020-3

RCLQRT-19V858-6454.PDF 211.434KB

 


Latest Recalls Documents

https://www-odi.nhtsa.dot.gov/acms/cs/documentList.xhtml?docId=19V858&docType=RCL

 


 

Bestseller No. 1
FOVPLUE 1.25" Highway pegs,Motorcycle Angled Adjustable Highway Footpegs for Harley Davidson Touring Road King Road Glide Street Glide Electra Glide Softail Sportster with 1 1/4" Highway Bar Black
  • ➤ Universal fits all models with 1.25" (32mm) highway engine guards such as For Harley For HondaeBay logo For SuzukieBay logo For KawasakieBay logo BMWeBay logo.For HondaeBay logo Goldwing GL1500 GL1100 GL1200 GL1800
  • ➤ Excellent replacement :Mounting clamp firmly grips the engine guard, and the locking design secures the peg at the desired angle
  • ➤Material: High Quality Metal & Rubber
  • ➤ In the box : Left and Right Angled Adjustable Highway Peg
  • ➤ Our Goal is 100% Customer Satisfaction :At FOVPLUE, our goal is 100% customer satisfaction. We take pride in providing exceptional customer service and free technical support. In the event you have a problem with your order, it’s our objective to make sure you are satisfied. If you have any issues with your order, please contact out knowledgeable customer service team or our technical support experts to resolve your issue
Bestseller No. 2
Universal Motorcycle Bicycle Folding Foot Pegs 90 Degree Foldable Electric Motorbike Ebike For Super73 S2/ZX/RX/R/S Passenger Footrests Rearsets Rear Set Footpegs foot Rest Pedals M8 Install Bolts
162 Reviews
Universal Motorcycle Bicycle Folding Foot Pegs 90 Degree Foldable Electric Motorbike Ebike For Super73 S2/ZX/RX/R/S Passenger Footrests Rearsets Rear Set Footpegs foot Rest Pedals M8 Install Bolts
  • Material: Make of High Quality Aluminum Alloy, It's Durable To Use.CNC Machined With High Precision And High Strength.
  • Size: 4.88inch x 0.98inch x 0.98inch ; Thread Size: M8x1.25; 2Sets Thread Length: 23mm(0.91") / 32mm(1.25").Weight: Approx. 300g ; Color: Black(Plating)
  • Knurled Anti-slip design offer great safety and comfort for passengers.New racing style makes your motorcycle even better and improve the body grade.Easy to install, installation Instructions is not Included, directly replace original foot pegs.
  • Fitment: Universal For Motorcycle, Bicycle, Bike, Electric Car Super73, ATVs, UTVs, Go Karts, Quads, Scooters which Use 8mm Install Bolts Fit for BMWeBay logo,HondaeBay logo,KawasakieBay logo,DucatieBay logo,SuzukieBay logo,YamahaeBay logo,ApriliaeBay logo,TriumpheBay logo, ApriliaeBay logo etc.
  • The support rod can be folded 90 degrees fixed, Can stay folded,this can be fixed in an "L" shape,with rebound front pedal and 90 degree rear pedal, light weight, high structural strength, and will not increase the weight of the motorcycle.
Bestseller No. 3
Hopider CNC Wide Foot Pegs 360° Roating MX Chopper Bobber Style for harley Dyna Sportster Fatboy Iron 883,Black
  • Fitments: Fits Most Harley Davidson models with male mount-style foot peg support. Fits models in passenger and highway peg positions
  • Durable and Light Weight: The foot pedals made of 7075-T6 Aluminum, one of the highest strenght alloys, can afford over 600KG pressure
  • Anti Slip: Removeable and replaceable sharp teeth made from hardened steel resist wear. It supply uniform and stable grip on your shoes during riding
  • 360° Roating: Footpegs can be rotated 360 degree to any angle and then locked down, you can find the most comfortable angle for your position
  • Size: The foot pegs base is 57mm wide and 88mm length. (Width: 2 1/4 inches, Length: 3 1/2 inches). Extra wide platform delivers solid footing for improved bike control
Bestseller No. 4
HDBUBALUS Motorcycle Foot Pegs Rest Male Mount Footpegs Billet Pedals Footrests Fit for Harley Touring Softail Sportster Dyna Road King
  • Fits For Harley models 1984-2025 with male mount-style footpeg supports. Not Fit for Rider Position on '17-later XG750A, 07-’10 XL883L, ’07-later XL883N, XL1200N, XL1200V and XL1200X, ’11-later XL1200C and XL1200T, '18-later XL1200NS and Xl1200XS, ’08-’13 XR and ’08-'17 FXCW, FXCWC, FXS, FXSB, FXSE and FXSBSE models and the rider and passenger position on '18-later Softail models).
  • Wide surface and large diameter end cap keep your boot in place. Perfect to upgrade your motorbike. Easy Installation
  • Slim foot peg design allows a comfortable pivot point. Narrow rubber bands and the knurled surfaces,effectively prevent skidding and excellent for foot fraction
  • Made of high quality aluminum material, anti-scratch, no faded after long time exposure;
  • Package: 1 Pair motorcycle foot pegs
Bestseller No. 5
Universal 8mm Foot Pegs CNC Aluminum Install Bolts Motorcycle Rearsets Footrest Footpegs Compatible With YAMAHA Honda Suzuki Kawasaki Ducati Aprilia
  • 【Features】: Cylinder shape carved with non-slipping wave grooves,Knurled anti-slip design offer great safety and comfort for passengers,New racing style makes your morcycle even better and improve the body grade
  • 【Material】 Made of T6063-T6 Aluminum,Anodized finishes to prevent from oxidizing and scratches, durable
  • 【Size】: 90mm X 25mm x 25mm/3.54" X 0.98" x 0.98"; Thread Size: M8 x 1.25; 1 pair Thread Length: 56.5mm(2.22 inch); Weight: Approx. 205g
  • 【Fitment】: Universal For 8mm Aprilla, BMWeBay logo, HondaeBay logo, KawasakieBay logo, , DucatieBay logo, SuzukieBay logo,YamahaeBay logo,TriumpheBay logo, MV AgustaeBay logo, Bimota, Buell, Momo Guzzi,etc, Scooters which use 8mm install bolts
  • 【Package】2 Foldable Foot Rest Pedal. Easy install,installation Instructions is not Included, directly replace original foot pegs

Last update on 2026-06-19 / Affiliate links / Images from Amazon Product Advertising API


 

This product presentation was made with AAWP plugin.

Leave a Comment

Share to...