NHTSA ID Number: 10171333
Manufacturer Communication Number: 059-726-00
Summary
Brake Assembly Kit for 7″, 10″ and 12″ Electric or Hydraulic Brakes Installation Instructions
1 Affected Product
Equipment
INSTALLATION INSTRUCTIONS
Brake Assembly Kit for 7”, 10” and 12” Electric or Hydraulic Brakes
Notice to Buyer
It is recommended that all brakes be replaced at the same time to ensure balanced braking performance.
Remove the old brakes
- Jack up trailer and secure on adequate capacity jack stands. Follow trailer manufacturers recommendations for lifting and supporting the unit.
| CAUTION |
| Do not lift or support the trailer on any part of the axle or suspension system. Never go under any trailer unless it is properly supported on jack stands which have been rated for the load. Improperly supported vehicles can fall unexpectedly and cause serious injury or death. |
- Remove the wheel and drum from the spindle, leaving the brake exposed. Check armature surface and drum braking surface. Resurface if required per your Operation Maintenance Service Manual.
- Disconnect the brake actuation system.
- Electric brakes
Cut the magnet wire and remove the strain relief from the dust shield.
Hydraulic brakes
Remove the hydraulic line from the wheel cylinder.
- Remove the brake mounting hardware. Then remove the old complete brake assembly and save the brake mounting hardware for installing the new brake.
Installing the new brakes
- Install the new brake assembly using the old hardware. If new hardware is required (or desired), select the correct components according to your brake size from the following chart.
| Brake Size | Qty | Part No. | Description |
| 7″ | 4 | 006-017-00 | 7/16-20 Hex Nut Torque 45-70 Ft. Lbs. |
| 10″ | 4 | 006-017-00 (2-3/8” Tube) | 7/16-20 Hex Nut Torque 45-70 Ft. Lbs. |
| 10″ | 4 | 006-207-00 (3” Tube) | 7/16-20 Hex Nut Torque 45-70 Ft. Lbs. |
| 12″ | 5 | 006-193-00 | 3/8-24 Hex Nut Torque 25-50 Ft. Lbs. |
- Reconnect the brake actuation system. Refer to Dexter
’s current Operation Maintenance Service Manual for proper connection. - Remount the drum and wheel. Refer to Dexter’s current Operation Maintenance Service Manual for proper bearing adjustment procedure.
- After replacement of brakes, the brakes must be re-burnished to seat the new components. This should be done by applying the brakes 20-30 times from an initial speed of 40 mph, slowing the vehicle to 20 mph. Allow ample time for the brakes to cool between applications. This procedure allows the new brake shoes to seat in to the drum surface.
Note: The current Dexter Axle Operation Maintenance Service Manual is available at www.dexteraxle.com.
059-726-00 | 2020.01
059-726-00
Bestseller No. 1
VEVOR Electric Trailer Brake Assembly, 12" x 2", 2 Pairs Self-Adjusting Electric Brakes Kit for 7000 lbs Axle, 5-Hole Mounting, Backing Plates for Braking System Part Replacement (2 Right + 2 Left)
- Self-Adjusting Electric Brake: Say goodbye to manual adjustments! Dive into the world of 12" x 2" electric trailer brake assemblies that self-adjust. It's not just smart; it's efficient and gives your trailer that smooth braking touch.
- Hassle-Free Installation: DIY's best friend! Our electric trailer brake is straightforward and a breeze to install. It's ready to install right out of the box and boasts high compatibility. Wherever you are, installation is just a few steps away.
- Built for the Long Haul: Keep on rolling! With a lifespan of up to 30,000 kilometers, these trailer brakes are in it for the long haul, designed for your trailer's daily adventures. Constructed from premium materials, our brakes promise robust durability and resistance to wear and tear.
- Versatility at Its Best: The trailer brake kit has a broad range of applications, including towing trailers, transporting goods, camping trips, and more. It's compatible with Dexter, AL-KO (a brand under the former), and other trailer axles.
- Top-Notch Packaging: When it comes to packaging, we don't just box; we care. Our trailer electric brake kit is packaged above industry standards. Every brake is meticulously checked and wrapped to ensure what you get is nothing short of perfect.
Bestseller No. 2
Trailer Axle Electric Brake Kit, Pair of 5-Hole, 4.5" Bolt Circle Brake Drum with 10" x 2 1/4" Self-Adjusting Electric Brakes for 3500 lb Axles, Replacement 10”(not for 4400lb) Brake Hub Drum Assembly
- Premium Material: This brake drum is made of high-quality iron and uses electroplating technology to protect the drum body, enabling it to work normally in various environments. At the same time, the brake drum is resistant to rust and corrosion, greatly extending the service life of the product.
- About The Drum and Self-Adjusting Electric Brakes: Classic design and rich production experience make the brake drum more excellent response, in a variety of harsh environments can achieve a short period of emergency braking, so that your journey is safer. It’s designed for 3500 lb Axles.
- Package Including: 2*brake drum 5 hole, 4.5" bolt, 2*Bearing inner ring replace for L68149( I.D:1.377", O.D:2.164"), 2*Bearing inner ring replace for L44649(I.D:1.062", O.D:2.058"), 2*grease seal(I.D: 1.718" O.D: 2.56" height: 0.5" ), 2*dust cover(Mounting diameter:1.988"), 2*rubber plug dust cover(Mounting diameter:1.988"), 10*hub nut(1/2-20 UNF-2B), 1*left electric brake, 1*right electric brake, 8*spring washer, 8*nut, 2* hexagon slotted nut, 2*flat washer, 2* cotter pin.
- Suit for: Pair of trailer 5 on 4.5" hub drum kits and 10" x 2 1/4" electric adjusting brakes fit for Dexter and other brands 3500lbs trailer axle. Fits 1-1/16'' to 1-3/8'' spindles 3,500 pounds trailer. Not fit for 1-1/16" Straight spindle and 1" Straight spindle.
- After Sale Service: High quality assurance! And we provide after-sales service policy. If you have any problems, please contact us first, we will try our best to solve your problem.
Bestseller No. 3
4Pcs 10" x 2-1/4" Electric Trailer Brake Assemblies for 3,500lbs, Left and Right
- Compatible with: Fit For Alko/ for Dexter/ for Quality, and other brands 3,500lbs trailer axle. Brake flange PCD: 4", Brake Flange Spacing between adjacent bolts: 2-7/8 inches. (Note: Not compatible with the 4400lbs axle)
- Kit Includes: 2x 10" x 2-1/4" left electric brake assemblies, 2x 10" x 2-1/4" right electric brake assemblies, 16x spring pad, 16x nut
- Function: good braking performance allows you to stop steadily in all road conditions.
- Product Introduction: The AEagle electronic brake features non-asbestos brake linings for superior friction performance, ensuring longevity and enhanced braking capabilities.
- Quality Assurance: 12-month warranty! Tested before shipping.
SaleBestseller No. 4
VEVOR Electric Trailer Brake Assembly, 12" x 2", 1 Pair Self-Adjusting Electric Brakes Kit for 7000 lbs Axle, 5-Hole Mounting, Backing Plates for Braking System Part Replacement (1 Right + 1 Left)
- Self-Adjusting Electric Brake: Say goodbye to manual adjustments! Dive into the world of 12" x 2" electric trailer brake assemblies that self-adjust. It's not just smart; it's efficient and gives your trailer that smooth braking touch.
- Hassle-Free Installation: DIY's best friend! Our electric trailer brake is straightforward and a breeze to install. It's ready to install right out of the box and boasts high compatibility. Wherever you are, installation is just a few steps away.
- Built for the Long Haul: Keep on rolling! With a lifespan of up to 30,000 kilometers, these trailer brakes are in it for the long haul, designed for your trailer's daily adventures. Constructed from premium materials, our brakes promise robust durability and resistance to wear and tear.
- Versatility at Its Best: The trailer brake kit has a broad range of applications, including towing trailers, transporting goods, camping trips, and more. It's compatible with Dexter, AL-KO (a brand under the former), and other trailer axles.
- Top-Notch Packaging: When it comes to packaging, we don't just box; we care. Our trailer electric brake kit is packaged above industry standards. Every brake is meticulously checked and wrapped to ensure what you get is nothing short of perfect.
Bestseller No. 5
Aeagle 5 on 4.5" Bolt Circle Drum Kits w/ 10" x 2-1/4" Left and Right Self-Adjusting Electric Brake for 3,500lbs Trailer Axle
- Compatible with: For Dexter/ for Al-Ko/ for Lippert/ for Quality and other brands 3,500lbs trailer axles; Only works on models for L68149 inner cone and replacement for L44649 outer cone bearings trailer axles, Only fits 1-1/16 to1-3/8 spindle axle. Brake flange PCD: 4". (Note: Not compatible with the 4400lbs axle)
- Kit Includes: 2x 5 on 4.5" brake drum, 2x inner cone bearing for L68149, 2x outer cone bearing for L44649, 2x oil seal, 2x dust cover, 2x rubber plug dust cover, 10x wheel hub nut, 2x electromagnetic self-adjusting brake (left+right), 8x spring washer, 8x nut, 2x hexagonal slotted nut, 2x flat washer, 2x split pin
- Compatible only with Standard Lube axles, Not fit for Nev-R-Lube axles, and not fit for Airstream Classic trailer(built after 7/2005)
- Product Process: The brake is made of high-quality gray cast iron with a rust resistant coating. Product is sturdy and durable, with a long use time
- Quality Assurance: 12-month warranty! Tested before shipping.
This product presentation was made with AAWP plugin.