Improperly Torqued Slide Pins On Brake Caliper – 2019-2020 Skeeter ZXR, FXR, WR, ZX, WX, SX, & Solera Series Boat Trailers

December 11, 2020 NHTSA CAMPAIGN NUMBER: 20V778000

Improperly Torqued Slide Pins On Brake Caliper

A dislodged brake caliper can cause a loss of trailer braking, increasing the risk of a crash.

 

NHTSA Campaign Number: 20V778

Manufacturer YamahaeBay logo Motor Corporation, USA

Components SERVICE BRAKES, HYDRAULIC

Potential Number of Units Affected 1,375

 

Summary

YamahaeBay logo Motor Corporation, USA (YamahaeBay logo) is recalling certain 2019-2020 Skeeter ZXR, FXR, WR, ZX, WX, SX, and Solera Series boat trailers. The slide pins in the brake caliper assemblies may have been improperly torqued or assembled with the incorrect locking agent, allowing the brake calipers to dislodge.

 

Remedy

Skeeter will notify owners, and dealers will tighten or, as necessary replace, the slide pins, free of charge. The recall began January 6, 2021. Owners may contact Skeeter customer service at 1-903-984-0541 or at www.skeeterboats.com.

 

Notes

Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.

 


Skeeter Boats

Trailer Brake Caliper Slider Pin Check

 

Checking Slider Pins

1) Remove the plastic caps from the rubber sleeves on the slider pins. Refer to the red arrow for their location.

2) Use a 7mm hex bit socket to check to make sure that each slider pin is torqued to 25 ftlbs.

3) If they do not turn and the torque wrench reaches 25 ft-lbs, they pass. If pin rotates before reaching 25 ft-lbs, check fails. Go to page 2 “Re-Torquing Caliper Pins” for further instructions.

4) Reinstall the plastic caps into rubber sleeves

5) All bolts that do not turn are considered complete. No further work is needed.

 

Re-Torquing Slider Pins

1) If the pin turns at all when torquing, it fails check. Remove the caliper pin.

2) Clean threads on pin with a dry rag and alcohol.

3) Blow out female threads in bracket with compressed air.

4) Screw pin in all the way to the shoulder to insure no trash present in threads, and remove/inspect pin again. Clean with alcohol if required.

5) Add blue locktite to the threads on the pins. Be sure all threads are coated evenly.

6) Screw pin in and torque to 25 ft – lbs.

7) Install the plastic cap into the rubber sleeve.

8) If pins are missing clean female threads as instructed above and install new pin per instructions that have been provided.

9) If pins are missing clean female threads as instructed above and install new pin torqueing to 2S ft -lbs. (Pins will be provided by Skeeter) A105:E129

10) If other damage is noted during completing this process please file a warranty claim using the normal Skeeter warranty process.

NOTE: There is a one hour labor allowance at shop rate to perform work described above.

 



2 Affected Products

Vehicle

MAKEMODELYEAR
SKEETERBOAT TRAILER2019-2020

 


8 Associated Documents

ISSUED Owner Notification Letter(Part 577)

RCONL-20V778-7862.pdf 75.452KB

 


Dealer Notification

RMISC-20V778-7593.pdf 59.937KB

 


Remedy Instructions and TSB

RCRIT-20V778-1599.pdf 151.617KB

 


Defect Notice 573 Report

RCLRPT-20V778-8418.PDF 215.795KB

 


Recall Acknowledgement

RCAK-20V778-2869.pdf 244.011KB

 


Recall Quarterly Report #1, 2021-1

RCLQRT-20V778-7109.PDF 211.141KB

 


Recall Quarterly Report #2, 2021-2

RCLQRT-20V778-9033.PDF 211.24KB

 


Recall Quarterly Report #3, 2021-3

RCLQRT-20V778-3620.PDF 211.321KB

 


Latest Recalls Documents

https://www-odi.nhtsa.dot.gov/acms/cs/documentList.xhtml?docId=20V778&docType=RCL

 


 

Bestseller No. 1
Bestseller No. 2
KODIAK 10 in -12 in Disc Brake Caliper Assembly, DAC DBC-225-DAC
  • HEAVY-DUTY DESIGN: Built for axle ratings between 3,500-6,000 lbs, this cast iron brake caliper delivers superior stopping power for heavy-duty applications
  • ENHANCED PISTON: Features a 2-1/4" diameter stainless piston
  • CORROSION PROTECTION: Dacromet plating ensures exceptional rust resistance and durability in both freshwater and saltwater environments
  • ROTOR COMPATIBILITY: Engineered to work with 10" & 12" diameter rotors, ensuring optimal braking system performance
  • PREMIUM CONSTRUCTION: Manufactured from high-quality cast iron with precision engineering for reliable, long-lasting brake performance
Bestseller No. 3
Dexter Kodiak Disc Brake Caliper w/Pads, 3500-6000 lbs Axle Rating, 2.25" Piston, Dacromet Plated
  • HEAVY-DUTY DESIGN: Built for axle ratings between 3,500-6,000 lbs, this cast iron brake caliper delivers superior stopping power for heavy-duty applications
  • ENHANCED PISTON: Features a 2-1/4" diameter stainless piston
  • CORROSION PROTECTION: Dacromet plating ensures exceptional rust resistance and durability in both freshwater and saltwater environments
  • ROTOR COMPATIBILITY: Engineered to work with 10" & 12" diameter rotors, ensuring optimal braking system performance
  • PREMIUM CONSTRUCTION: Manufactured from high-quality cast iron with precision engineering for reliable, long-lasting brake performance
Bestseller No. 4
SOUTHWEST WHEEL 3,500-6,000 lbs. Trailer Axles Gold Zinc Plated Finish Disc Brake Caliper w/Ceramic Pads
  • Fit's 3500-6000 lbs. Trailer Axles
  • Will work with Kodiak and DeeMaxx Disc Brakes
  • Will work with 10" or 12" Rotors
  • Gold Zinc Plated Finish
  • Floating Design

Last update on 2026-06-19 / Affiliate links / Images from Amazon Product Advertising API


 

This product presentation was made with AAWP plugin.

Leave a Comment

Share to...