October 16, 2019 NHTSA CAMPAIGN NUMBER: 19V739000
An air hose that drags on the ground may leak air, possibly increasing the risk of a crash.
NHTSA Campaign Number: 19V739
Manufacturer Hyundai
Translead
Components SERVICE BRAKES, AIR
Potential Number of Units Affected 34,960
Summary
Hyundai Translead is recalling certain 2018-2019 Dry Van Trailers. The beam clip of the air hose spring assembly may detach from the beam allowing the air hoses to drag on the ground.
Remedy
Hyundai Translead will notify owners, and dealers will replace the beam clip, free of charge. The recall began November 12, 2019. Owners may contact Hyundai Translead customer service at 1-800-251-0871.
Notes
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.
Service Bulletin on Cross Member Beam Clips
Incident Report
Description of Issue:
The beam clip used on this trailer which holds the spring / airlines could potentially fail causing it to detach from the cross member. As such, the beam clip needs to be replaced.
Inspection Procedure
Inspection:
- Visually inspect the unit to identify the number of gray colored beam clips installed.
Corrective Action
Repair Procedure:
- Prepare the tools you’ll need to replace the current gray colored beam clip. Set should include a hammer, pliers, and a new Zinc and yellow clip(s).
- With a hammer, tap the current gray colored beam clip backwards without twisting or bending the spring until it comes off of the cross member. Make sure to mark the current location of the existing beam clip prior to removal to ensure that the new beam clip is placed in the same location and functions properly. Failure to install the clip in the correct location could cause spring malfunction or rubbing of hoses.
- Proceed to remove the current gray colored beam clip from the spring by holding it in one hand and the spring in the other hand and slowly twisting the beam clip counterclockwise off the end loop of the spring without twisting or bending the spring.
- Insert the new Zinc and yellow beam clip into the spring by placing the tab of the beam clip between the coils of the end loop and twisting clockwise (without twisting or bending the spring) until it is fully onto the spring and secure.
- Once you place the new Zinc and yellow beam clip into the end loop of the spring, proceed to reattach the clip to the cross member.
- Pick up the new Zinc and yellow colored beam clip with the pliers and place it in the same location where the removed gray beam clip was installed.
- Then use your hammer to attach the new Zinc and yellow beam clip to the cross member with the eyelet of the clip facing down and the spring hanging straight. Do not twist or bend the spring during the installation process as this could cause it to malfunction.
- Finally, inspect the newly attached Zinc and yellow colored beam clip to ensure it is fully attached and the spring is hanging straight.
** You may also refer to the beam clip removal and replacement installation video should you need visual guidance **
NOTE: Clips are not reusable and as such should not be taken off and reinstalled. Please make a record of the beam clip removal and replacement process and dispose of the gray beam clip(s) you removed.
Labor Time:
Total time allotted to inspect, remove, and replace beam clip(s) is 15 minutes per trailer
2 Affected Products
Vehicle
7 Associated Documents
Recall Quarterly Report #2, 2020-1
RCLQRT-19V739-7288.PDF 211.225KB
Recall Quarterly Report #1, 2019-4
RCLQRT-19V739-9134.PDF 211.12KB
Recall Acknowledgement
Safety Bulletin
RCSB-19V739-7603.pdf 231.491KB
Defect Notice 573 Report
RCLRPT-19V739-6047.PDF 212.955KB
Recall Quarterly Report #4, 2020-3
RCLQRT-19V739-8828.PDF 211.414KB
Recall Quarterly Report #3, 2020-2
RCLQRT-19V739-7451.PDF 211.414KB
Latest Recalls Documents
- Product Type:Auto Part
- Item Package Dimensions:4.0 " L X 8.0 " W X 4.0 " H
- Item Package Weight:1.0 lbs
- Country Of Origin: United States
- Fit type: Vehicle Specific
- Abundant in quantity: the package comes with 50 pieces of trailer wire clips, can be widely applied in your daily life, sufficient for your using demands; With such a large quantity, you can also share the wire clips for trailer with your family members or friends generously, bringing them lots of convenience
- Reliable workmanship for lasting service: made of quality stainless steel, the double wire stainless steel clips are sturdy in structure, well polished with no pointed edges, hardly fading or rusting; Moreover, the wire clamps for electric wires adopt barbed and curved design, can hold 2 wires tightly and neatly at the same time, not easy to falling off, keeping the wires from tangling
- Compact and portable: the trailer clips are designed with a total length of approx. 22.5 mm/ 0.89 inches, convenient for you to store them and carry around; The applicable cable diameter of the trailer light clips ranges from approx.6 mm/ 0.24 inches to approx. 6.5 mm/ 0.26 inches, can be applied to panels that are approx. 1.3 mm/ 0.05 inches to approx. 2.5 mm/ 0.1 inches in width
- Convenient to apply: you can finish installing the wire panel clips in a few seconds, just clip them on targeted positions by hand, no tools or instructions needed, not occupying too much time and energy; To manage your wires, you just need to clip them on the wire frame clips, 2 wires for each clip, and it's also easy for you to remove them, leaving no traces on your panels or wires
- Multiple using occasions: there is a wide range of occasions for the wire harness clips, for example, you can apply the trailer wiring harness clips to kayaks, fishing boats, trailers, workbenches, offices and more, helping you organize your wires and cables, thus keeping them tidy, saving you space
- SIMPLIFIED OVERHEAD CABLE MANAGEMENT - ICC 2" Beam Clamp J-Hooks provides a practical solution for organizing and securing cables overhead. With a practical design and function, each J-Hook helps prevent tangled wires and keep cables neatly routed, providing proper support for category cables, fiber optic cables, inter-duct systems, and other low-voltage cabling requirements.
- 24pcs Trailer floor/deck hold down clips bearclaw.
- Size: 1-1/4" wide, 3" long, and about 3/16" thick plate.
- Fit for 5/16" or 3/8" bolt.
- Made of heavy duty steel, it not only has a stable structure and reliable performance, but also has excellent durability, which can meet long-term use needs.
- Easy-to-install deck floor clips require no drilling. simply hammer these trailer deck anchors into place for quick wood or composite decking setup.
- Massive Supply, Maximum Efficiency: Each bulk pack contains 50 pcs premium beam flange clips engineered for secure attachment of wires, S-hooks, and chains. Designed for 1/8" to 1/4" flange thicknesses, these clips ensure you have a steady supply for large-scale installations or rapid maintenance
- Reliable Material Construction: crafted from sturdy steel, these flange clips resist rust, wear, and deformation; The material maintains structural integrity under pressure, ensuring long-term functionality in various environments
- Rapid-Install Hammer-On Design: Experience lightning-fast setup with our side-mount flange clips. No complex tools or drilling required—simply align and secure with a single hammer strike. This streamlined design significantly slashes labor time and simplifies even the most demanding assembly or repair tasks
- Versatile Application: ideal for attaching wires, hooks, chains, or other components to flanges and profiles; Its adaptable design supports multiple configurations, catering to diverse project requirements
- Indoor Outdoor Adaptability: suitable for both interior and exterior use, these flange clips perform consistently in different settings; Whether for home DIY tasks or commercial installations, they deliver reliable performance
This product presentation was made with AAWP plugin.