Wheel Lug Nuts may Loosen – 2016-2020 Vermeer Brush Chipper Trailers

SEOCONTENT-START

DUAL HORIZONTAL OFFSET FEED ROLLERS.
Improve performance by aggressively grabbing
and feeding material to the drum. The offset helps
the upper feed roller climb over big logs or
material with lots of branches and forks.
EASILY LIFTS HEAVY MATERIAL. An optional
winch allows operators to move large logs
effortlessly. The 150′ (45.7 m) winch line can
handle logs up to 2000 lb (907.2 kg) and can be
used to lift the log onto the feed table.
ELECTRONIC FUEL INJECTION ENGINE.
With improved fuel economy, the 135 horsepower
(101 kW) Power Solutions International (PSI)
engine allows for more effi cient working
conditions and boosts engine response under load.
A CLUTCHLESS PTO SYSTEM. Avoids
premature wear to the belt-drive system by
preventing high-speed engagement of the cutter
drum. The throttle is integrated with the belt drive
to help ensure the PTO can be engaged only while
the engine is at low speed.
EXTENDED WARRANTY. The 3-year/
3000-hour extended limited warranty on drum
housing, cutter drum, shaft and ring-fetter hubs
offers you peace of mind, in addition to the
1-year/1000-hour Vermeer equipment
limited warranty.
ECOIDLE™ ENGINE CONTROL SYSTEM.
When the EcoIdle function is selected by the
operator, the engine speed automatically lowers
to a preset rpm after 1 minute or 5 minutes of
inactivity to help reduce fuel consumption when
not chipping material. Due to this idling, noise and
greenhouse emissions are also reduced.
VERMEER.COM
GAS BRUSH CHIPPER
BC1200XL
EiC::~IIC>LE:™
Vermeer· y
EQUIPPED TO
DO MORE:
GENERAL
Length: 168″ (426.7 cm)
Width: 79″ (200.7 cm)
Height: 103″ (261.6 cm)
Weight (with winch): 6450 lb (2925.7 kg)
Weight: 5680 lb (2576.4 kg)
ENGINE
Make/Model: PSI 4.XL Electronic Fuel Injection
Horsepower: 135 hp (101 kW)
Max torque: 258 ft-lb (349.8 Nm) @1400 rpm
Fuel type: Gasoline
Number of cylinders: 6
Cooling medium: Liquid
CUTTING SYSTEM
Drum dimensions: 20″ diameter x 20″ wide (50.8 cm x 50.8 cm)
Drum speed: 2000 rpm
Knives: Two A8 chipper steel
Bedknife: Four usable edges
FEED SYSTEM
Chipping capacity (max): 13.3″ (33.8 cm)
Infeed opening height: 32″ (81.3 cm)
Infeed opening width: 52″ (132.1 cm)
Feed roller orientation: Dual horizontal offset
Feed table height: 32″ (81.3 cm)
Feed speed (max): 110 fpm
Feed roller dimensions (upper roller): 15″ (38.1 cm) diameter x
17″ (43.2 cm)
Feed roller dimensions (lower roller): 11.1″ (28.2 cm) diameter x
17″ (43.2 cm)
CAPACITIES/ELECTRICAL
Fuel tank: 25 gal (94.6 L)
Hydraulic tank: 12 gal (45.4 L)
System voltage: 12 V
Lights: LED brake, turn, tail, license, side indicators
CHASSIS/BRAKES
Frame: 7″ x .25″ (17.8 cm x .6 cm) Z-channel
Tires (option 1): ST235/80/R16 Load Range E
Tires (option 2): ST285/75/R16 Load Range E
Axle/Suspension: 7000 lb (3175.2 kg) rubber torsion
Electrical brakes with breakaway switch
BC1200XL GAS BRUSH CHIPPER
Vermeer Corporation reserves the right to make changes in engineering, design and specifications; add improvements; or discontinue manufacturing at any time without notice or obligation. Equipment
shown is for illustrative purposes only and may display optional accessories or components. Please contact your local Vermeer dealer for more information on machine specifications. Vermeer, the Vermeer
logo, EcoIdle, Equipped to Do More and Vermeer Confidence Plus are trademarks of Vermeer Manufacturing Company in the U.S. and/or other countries. PSI is a trademark of Power Solutions International Inc.
© 2016 Vermeer Corporation. All Rights Reserved. Printed in the U.S.A. Please recycle.
PN 180007865
OPTIONS
Extended warranty
Special paint
Planned maintenance
Vermeer Confidence Plus® asset protection program
NOTES:
08/16.50
***************************************************************************

OFFSET HORIZONTAL FEED ROLLERS.
The offset horizontal feed rollers are designed to
efficiently take on oversized, branchy limbs.
ROBUST FEED TABLE. Mechanized feeding
is made convenient with a 28.9″ (72.4 cm)
feed roller opening and a durable, fixed infeed
table design.
SMARTCRUSH. Increase jobsite productivity
with the SmartCrush system that includes
intuitive hydraulic crushing capabilities to
minimize chainsaw work.
POWERFUL PERFORMANCE. Equipped with up
to 11,674 lb (5295.2 kg) of pull-in force, this unit
has optimized efficiency while working in tandem
with the patented SmartFeed system to increase
productivity when chipping large diameter logs.
OPERATOR CONTROL. The Tree Commander™
remote control comes standard with the AX19,
and an optional full-function remote is available.
The operator is able to control the functions
of the brush chipper remotely to improve
jobsite productivity.
OPTIONAL WINCH. The 150′ (45.7 m) winch line
has a pull-in force of 3250 lb (1474.2 kg), making
it easy to lift logs directly onto the feed table.
The winch boom can be removed and installed
conveniently with just six bolts. By removing the
winch boom, the operator can mechanically feed
the chipper more efficiently.
VERMEER.COM
BRUSH CHIPPER
AX19
Vermeer· y
EQUIPPED TO
DO MORE:
AX19 BRUSH CHIPPER
NOTES:
GENERAL
Length: 221″ (561.3 cm)
Height: 108″ (274.3 cm)
Width: 79″ (200.7 cm)
Weight (without winch and hydraulic jack): 11,200 lb (5080.3 kg)
Weight (with winch): 11,650 lb (5284.4 kg)
CAPACITIES/ELECTRICAL
Fuel tank: 40 gal (151.4 L)
Hydraulic tank: 20 gal (75.7 L)
Max hydraulic flow: 14.8 gpm (56 L/min)
DEF tank: 5 gal
Lights: LED front, rear, side, brake and taillights
CHASSIS/BRAKES
Frame: Z channel, 7.5″ x .25″ thick (19.1 cm x .64 cm)
Tires: LT285/75R16 load range E
Axle/suspension: Tandem torsion 7000 lb capacity (3175.1 kg)
Hitch: Pintle
CUTTING SYSTEM
Drum speed: 1100 rpm
Drum dimensions: 36″ (91.4 cm) diameter
Drum thickness: .5″ (1.3 cm)
Knives: 4 knives – 5.5″ x 10″ x .625″ (14 cm x 25.4 cm x 1.6 cm)
Shear bar: 4-sided – 3″ x 20.25″ x 1.25″ (7.6 cm x 51.4 cm x 3.2 cm)
Engagement system: Automotive style clutch
FEED SYSTEM
Chipping capacity: 19″ (48.3 cm)
Infeed opening height: 24″ (61 cm)
Infeed opening width: 28.9″ (73.4 cm)
Feed roller orientation: Horizontal
Feed table height: 35″ (88.9 cm)
Feed speed (max): 119 fpm (36.3 m/min)
Feed roller dimensions: 19″ dia x 28.25″ length (48.3 cm x 71.8 cm)
DISCHARGE SYSTEM
Discharge height: 108″ (274.3 cm)
Degree of rotation: 270°
ENGINE
Make/model: John Deere 4045HFC09
Gross horsepower: 173 hp (129 kW)
Max torque: 492 ft-lb (667.1 Nm)
Fuel type: Diesel
Number of cylinders: 4
OPTIONS
Special paint
Extended warranty
Preventive maintenance
Adjustable height discharge chute
Full function remote control
Manual outriggers
Hydraulic jack
Vermeer Corporation reserves the right to make changes in engineering, design and specifications; add improvements; or discontinue manufacturing at any time without notice or obligation. Equipment shown is
for illustrative purposes only and may display optional accessories or components. Please contact your local Vermeer dealer for more information on machine specifications. Vermeer, the Vermeer logo, Equipped
to Do More and Tree Commander are trademarks of Vermeer Manufacturing Company in the U.S. and/or other countries. John Deere is a trademark of Deere & Company. © 2016 Vermeer Corporation. All Rights
Reserved. Printed in the U.S.A. Please recycle.
10/16.5k PN 180026148
*****************************************************************************************

CHIPPING PRODUCTIVITY. The SmartFeed
system monitors engine rpm and automatically
stops and reverses the feed rollers to enhance
production. This system also senses feed roller
jams and manipulates the material automatically
to reduce the need for manual control bar use.
EASILY LIFT HEAVY MATERIAL. An optional
winch allows operators to move large logs
effortlessly. The 150′ (45.7 m) winch line can
handle logs up to 2000 lb (907.2 kg) and can
automatically lift the logs onto the feed table.
OPERATOR SAFETY. Mounted over the feed
table, the four-position upper feed control bar
enables the operator to stop the feed rollers and
select forward/reverse. The patented bottom feed
stop bar is strategically located to make it possible
for an operator’s leg to strike the bar and shut
off the feed mechanism either intentionally or
automatically in an emergency situation.
TAKE CONTROL. With the optional Tree
Commander™ remote control, jobsite productivity is
improved by allowing the operator to control brush
chipper functions remotely. The remote can be
attached to the operator’s belt or held in an optional
bracket mounted directly to the operator’s station of
a Vermeer compact utility loader.
ECOIDLE™ ENGINE CONTROL SYSTEM.
When the Ecoldle function is selected by the
operator, the engine speed automatically lowers
to a preset rpm after one or fi ve minutes of
inactivity to help reduce fuel consumption when
not chipping material. Due to this idling, noise and
greenhouse emissions are also reduced.
SMOOTH FEEDING. Vertical feed rollers with
helical cleats help hold material fi rmly to the
infeed table, which reduces vibration, shock and
structural loading to the rear of the machine.
VERMEER.COM
BRUSH CHIPPER
BC1500
Vermeer· y
EQUIPPED TO
DO MORE:
Vermeer Corporation reserves the right to make changes in engineering, design and specifications; add improvements; or discontinue manufacturing at any time without notice or obligation.
Equipment shown is for illustrative purposes only and may display optional accessories or components. Please contact your local Vermeer dealer for more information on machine specifications.
Vermeer, the Vermeer logo, Equipped to Do More, Tree Commander, Ecoldle and Vermeer Confidence Plus are trademarks of Vermeer Manufacturing Company in the U.S. and/or other countries.
Cummins is a trademark of Cummins Inc. John Deere is a trademark of Deere & Company. © 2017 Vermeer Corporation. All rights reserved. Printed in the U.S.A. Please recycle.
BC1500 BRUSH CHIPPER
PN 296431562
GENERAL
Length: 179″ (454.7 cm)
Height: 104″ (264.2 cm)
Width: 86″ (218.4 cm)
Weight (without winch): 7490 lb (3397.4 kg)
Weight (with winch): 7800 lbs (3538 kg)
CAPACITIES/ELECTRICAL
Fuel tank: 45 gal (170.3 L)
Max hydraulic flow: 5.5 gpm (20.8 L/min)
DEF tank: 5 gal (18.9 L)
Lights: LED front, rear, side, brake and taillights
CHASSIS/BRAKES
Frame: .25″ (6.4 mm) Z channel, 7″ (17.8 cm)
Tires: LT 285/75R16 LR E
Axle/Suspension: Torsion
CUTTING SYSTEM
Drum speed: 2208 rpm
Drum cutting diameter: 23.8″ (60.5 cm)
Drum thickness: .375″ (.95 cm)
Knives: 2 knives – .625″ x 5″ x 8″ (1.6 cm x 12.7 cm x 20.3 cm)
Engagement system: Automotive-style clutch
FEED SYSTEM
Chipping capacity: 15″ (38.1 cm)
Infeed opening height: 18.3″ (46.5 cm)
Infeed opening width: 15.8″ (40.1 cm)
Feed roller orientation: Vertical
Feed table height: 32″ (81.3 cm)
Max feed speed: 125 fpm (38.1 m/min)
Feed roller diameter: 21″ (53.3 cm)
DISCHARGE SYSTEM
Discharge height: 104″ (264.2 cm)
Degree of rotation: 270°
ENGINE OPTION ONE
Make/Model: Cummins QSF3.8L Tier 4 Final
Gross horsepower: 130 hp (97 kW)
Max torque: 360 ft-lb (488.1 Nm)
Fuel type: Diesel
Number of cylinders: 4
ENGINE OPTION TWO (INTERNATIONAL)
Make/Model: John Deere 4045H Tier 3
Gross horsepower: 125 hp (93 kW)
Max torque: 355 ft-lb (481.3 Nm)
Fuel type: Diesel
Number of cylinders: 4
OPTIONS
Tree Commander™ remote control
Extended warranty
Special paint
Planned maintenance
Vermeer Confidence Plus® asset protection program
Winch
Hydraulic chute rotate
01/18.2k
Contact your local Vermeer dealer for engine availability in your region.
***********************************************************************************

OPERATOR SAFETY. Combined with the
patented bottom feed stop bar is the four-position
upper feed control bar with dual stop positions and
forward/reverse feed positions. Mounted over the
feed table, it enables the operator to stop the feed
rollers and select forward or reverse operations.
Dual reset/hold-to-run buttons allow the operator
to readily reset the bottom feed stop bar.
ECOIDLE™ ENGINE CONTROL SYSTEM.
The EcoIdle engine control system can help aid in
noise reduction, as well as help consumer less fuel
if the feeding process has frequent interruptions.
SMARTFEED. The patented SmartFeed system
helps increase operator productivity while
reducing strain on vital engine parts.
The feedsensing control system monitors engine
rpm and automatically stops and reverses the
feed roller when feeding larger, hardwood material.
LARGE FEED OPENING. A large rectangular
12” x 17” (30.5 cm x 43.2 cm) feed opening helps
boost productivity by reducing the need to trim
material before feeding it into the chipper.
EXTENDED WARRANTY. The 3-year/3000-hour
extended limited warranty on drum housing, cutter
drum, shaft and hubs offers peace of mind,
in addition to the 1-year/1000-hour Vermeer
equipment limited warranty.
CLUTCHLESS PTO. The throttle integrated with
the belt drive engagement process helps ensure
that the PTO can only be engaged while the engine
is at low idle/low rpm. Automatically, the engine
throttles up to full rpm after the belt drive is fully
engaged. This system helps to reduce premature
wear to the belt drive system by preventing high
idle engagement of the cutter drum.
VERMEER.COM
BRUSH CHIPPER
BC1000XL
GENERAL
Length: 150″ (381 cm)
Width: 66.5″ (168.9 cm)
Height: 101″ (256.5 cm)
Weight: 4995 lb (2265.7 kg)
ENGINE OPTION ONE
Make and model: Deutz D2.9L Tier 4 Final
Horsepower: 49 hp (36.5 kW)
Max torque: 108 ft-lb (146.2 Nm)
Fuel type: Diesel
Number of cylinders: 4
Cooling medium: Liquid
CUTTING SYSTEM
Drum dimensions: 20″ diameter x 20″ wide (50.8 cm x 50.8 cm)
Drum speed: 2050 rpm
Knives: Two A8 chipper steel reversible
Shear bar: Four usable edges
Engagement system: Clutchless belt drive PTO
CAPACITIES/ELECTRICAL
Fuel tank: 25 gal (94.6 L)
Hydraulic tank: 7 gal (26.5 L)
Hydraulic flow (max): 2.7 gpm (10.2 L/min)
Electrical: 12 Volt
Lights: LED stop, turn, tail, license
BC1000XL BRUSH CHIPPER
ENGINE OPTION TWO
Make and model: Deutz TD2.9L Tier 4 Final
Horsepower: 74 hp (55 kW)
Max torque: 181 ft-lb (245.4 Nm)
Fuel type: Diesel
Number of cylinders: 4
Cooling medium: Liquid
CHASIS/BRAKES
Frame: .25″ x 7″ (63.5 cm x 17.8 cm) Z channel
Tires: ST235/80/R16 load range E
Axle/Suspension: 5200 lb (2359 kg)/Torsion
Optional axle/suspension: 7000 lb (3175.1 kg)/Torsion
Electric brakes with breakaway switch
OPTIONS
Extended warranty
Special paint
Planned maintenance
Vermeer Confidence Plus® Asset Protection Program
Hydraulic surge brakes
Tree Comander™ remote control
FEED SYSTEM
Chipping capacity (max): 12″ (30.5 cm)
Infeed opening height: 12″ (30.5 cm)
Infeed opening width: 17″ (43.2 cm)
Feed roller orientation: Single horizontal
Feed table height: 26″ (66 cm)
Feed speed (max): 105 fpm (32 m/min)
Feed roller dimensions: 20″ x 17″ (50.8 cm x 43.2 cm)
NOTES:
Vermeer Corporation reserves the right to make changes in engineering, design and specifications; add improvements; or discontinue manufacturing at any time without notice or obligation.
Equipment shown is for illustrative purposes only and may display optional accessories or components. Please contact your local Vermeer dealer for more information on machine specifications.
Vermeer, the Vermeer logo, Equipped to Do More, EcoIdle, Tree Commander and Vermeer Confidence Plus are trademarks of Vermeer Manufacturing Company in the U.S. and/or other countries.
Deutz is a trademark of Klockner-Humboldt-Deutz Corporation. © 2015 Vermeer Corporation. All Rights Reserved. Printed in the U.S.A. Please recycle.
PN 180007890

********************************************************************************************

 SEOCONTENT-END