December 16, 2019 NHTSA CAMPAIGN NUMBER: 19V893000
Brake Relay Valve Air Flow Restriction/FMVSS 121
An increase in stopping distance increases the risk of crash.
NHTSA Campaign Number: 19V893
Manufacturer Foretravel
, Inc.
Components SERVICE BRAKES
Potential Number of Units Affected 5
Summary
Foretravel, Inc. (Foretravel) is recalling certain 2020 Realm and iH45 vehicles built on a Spartan chassis. The brake relay valve may have an air flow restriction, which may result in an extended stopping distance. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 121, “Air Brake Systems.”
Remedy
Foretravel will notify owners, and Spartan dealers will inspect and replace the valves, free of charge. The recall began December 16, 2019. Owners may contact Foretravel customer service at 1-800-955-6226.
Notes
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.
Recall Service Bulletin
| DATE: | 7/23/19 |
| APPLIES TO: | This Recall service bulletin applies to certain 2018 and 2019 model year Gladiator and MetroStar model Emergency Response chassis cabs built between January 9, 2019 and March 12, 2019. |
| NHTSA/TC Id: | 19V-360 |
| CONDITION: | Certain vehicle configurations fail to meet service brake application timing requirements identified in Federal Motor Vehicle Safety Standard No. 121- Air brake systems. |
| CORRECTION: | Remove and replace Relay Valve |
| LABOR ALLOCATION: | 1h for R&R of relay valve |
| CLASSIFICATION: | V3 |
PARTS NEEDED:
| QTY | Part Number | Description |
| 1 | S-2709-001 | Kit- Service, Relay Valve, Fire Truck |
| Kit # S-2709-001 Contains: | ||
| QTY | Part Number | Description |
| 1 | 0918-MM5-017 | Valve, Relay 0 PSI Crack |
| 1 | RSB19-330-005 | Instruction Document |
| 1 | RSB19-330-006 | Instruction Document |
GENERAL INSTRUCTIONS:
Thoroughly review entire service bulletin before starting work. If there are questions or concerns with steps defined in this service bulletin, contact Spartan Motors USA, Inc. Customer & Product Support Group.
All applicable industry safety standards must be followed when performing work identified in this procedure.
STEP-BY-STEP INSTRUCTIONS:
- Tilt Firetruck cab. Make sure of the following before tilting cab:
- Secure all items in cab
- Check for clearances around cab
- Make sure cab is tilted high enough to engage safety latch
- Locate relay valve located behind drive side step well. Refer to FIG. 2-1.
FIG. 2-1
- Remove relay valve. Be sure to mark all hoses for reinstallation.
- Install new relay valve per Diagram 1.
-
- Torque 5/16-18 nuts to 119 lbf-in.
- Refer to Appendix A for fitting installation instructions.
Appendix A
Fitting Installation
IMPORTANT SAFETY RECALL NOTICE
19V893
This notice applies to the vehicle identification number below
Dear Foretravel Owner:
This notice is sent to you in accordance with the requirements of the National Traffic and Motor Vehicle Safety act.
Foretravel Inc. has decided that a defect which relates to motor vehicle safety exist in certain Realm and IH45 motor home chassis built between December 7, 2018 and March 5, 2019 by Spartan Motors.
Please note: The Vehicle Identification Number that may be affected by this recall is located at the top of this letter.
What is the defect?
Foretravel has been notified by Spartan Motors that vehicles affected by this recall may be equipped with brake relay valves in which an orifice within the valve may be restricted inhibiting air flow. The restriction of air flow can cause the affected vehicles to fail to comply with the service brake application timing requirements S5.3.3.1 (a) With an initial service reservoir system air pressure of 100 psi, the air pressure in each brake chamber shall, when measured from the first movement of the service brake control, reach 60 psi in not more than 0.45 second in the case of trucks and buses. Depending on the amount of restriction, an increase in the application of the se1vice brakes may result in an increase in stopping distance which may result in a crash.
Corrective Action
Foretravel will issue owner and dealer notifications to have the valve inspected and if needed, replaced at no charge to you, the vehicle owner. All vehicles affected by this recall are within their warranty period and any identified non-conforming parts would be replaced through Warranty.
What Should You Do
Please contact Foretravel Inc. at 1-800-955-6226 opt 3 to locate a qualified se1v ice center near you. Steps will be taken to ensure the recall is performed at the nearest se1vice center.
Reimbursement
The labor time necessary to perform this service correction is approximately 2 hours for removal and replacement. If you had this repair performed before you received this letter, you may be eligible to receive reimbursement for the cost of obtaining a pre-notification remedy of the problem associated with this recall. For more information contact Foretravel Inc., at 1-800-955- 6226 opt. 3.
Reply Card
The enclosed owner reply card identifies your vehicle. Presentation of this card to the service center will assist in making the necessary correction in the shortest possible time. If you have sold or traded the vehicle, please let us know by completing the postage paid reply card and returning it to us.
If the authorized service center has failed or is unable to remedy the defect without charge and within a reasonable time, contact Foretravel Inc. at 1-800-955-6226 opt. 3. If you are still not able to have the safety defect remedied without charge and within a reasonable time, you may wish to write the Administrator, National Highway Traffic Safety Administration, 1200 New Jersey Avenue SE, Washington, D.C. 20590 or call the Auto Safety Hotline at 1-888-327-4236 (TTY: 1-800-424-9153); or go to https://v.rww.safecar.gov if you feel the manufacture has failed or is unable to remedy the defect without charge.
Foretravel apologizes for this inconvenience; however, we have taken this action in the interest of your safety and continued satisfaction with our products.
Sincerely,
Ronnie Blackmon
Director of Warranty and Customer Service
SEOCONTENT-START
Recall Service Bulletin
Page 1 of 4 QUA-FR-0291
Rev: 3.0
19012
Service Bulletins are intended for use by Professional Technicians only. They are written to guide Professional Technicians in performing service to
vehicles of specific nature in conjunction with industry standards. Professional Technicians are appropriately trained on industry standards and have
the tools and equipment to perform procedures safely and properly.
DATE: 7/23/19
APPLIES TO: This Recall service bulletin applies to certain 2018 and 2019 model year
Gladiator and MetroStar model Emergency Response chassis cabs built
between January 9, 2019 and March 12, 2019.
NHTSA/TC Id: 19V-360
CONDITION: Certain vehicle configurations fail to meet service brake application
timing requirements identified in Federal Motor Vehicle Safety Standard
No. 121- Air brake systems.
CORRECTION: Remove and replace Relay Valve
LABOR ALLOCATION: 1h for R&R of relay valve
CLASSIFICATION: V3
PARTS NEEDED:
QTY Part Number Description
1 S-2709-001 Kit- Service, Relay Valve, Fire Truck
Kit # S-2709-001 Contains:
QTY Part Number Description
1 0918-MM5-017 Valve, Relay 0 PSI Crack
1 RSB19-330-005 Instruction Document
1 RSB19-330-006 Instruction Document
GENERAL INSTRUCTIONS:
Thoroughly review entire service bulletin before starting work. If there are questions or concerns
with steps defined in this service bulletin, contact Spartan Motors USA, Inc. Customer & Product
Support Group.
All applicable industry safety standards must be followed when performing work identified in this
procedure.
Recall Service Bulletin
Page 2 of 4 QUA-FR-0291
Rev: 3.0
19012
Service Bulletins are intended for use by Professional Technicians only. They are written to guide Professional Technicians in performing service to
vehicles of specific nature in conjunction with industry standards. Professional Technicians are appropriately trained on industry standards and have
the tools and equipment to perform procedures safely and properly.
STEP-BY-STEP INSTRUCTIONS:
1. Tilt Firetruck cab. Make sure of the following before tilting cab:
• Secure all items in cab
• Check for clearances around cab
• Make sure cab is tilted high enough to engage safety latch
2. Locate relay valve located behind drive side step well. Refer to FIG. 2-1.
FIG. 2-1
3. Remove relay valve. Be sure to mark all hoses for reinstallation.
4. Install new relay valve per Diagram 1.
a. Torque 5/16-18 nuts to 119 lbf-in.
5. Refer to Appendix A for fitting installation instructions.
Recall Service Bulletin
Page 3 of 4 QUA-FR-0291
Rev: 3.0
19012
Service Bulletins are intended for use by Professional Technicians only. They are written to guide Professional Technicians in performing service to
vehicles of specific nature in conjunction with industry standards. Professional Technicians are appropriately trained on industry standards and have
the tools and equipment to perform procedures safely and properly.
Diagram 1
Recall Service Bulletin
Page 4 of 4 QUA-FR-0291
Rev: 3.0
19012
Service Bulletins are intended for use by Professional Technicians only. They are written to guide Professional Technicians in performing service to
vehicles of specific nature in conjunction with industry standards. Professional Technicians are appropriately trained on industry standards and have
the tools and equipment to perform procedures safely and properly.
Appendix A
Fitting Installation
2 Affected Products
Vehicles
| MAKE | MODEL | YEAR |
| FORETRAVEL | IH45 | 2020 |
| FORETRAVEL | REALM | 2020 |
6 Associated Documents
Owner Notification Letter(Part 577)
RCONL-19V893-6138.pdf 354.537KB
Recall Quarterly Report #2, 2020-1
RCLQRT-19V893-5036.PDF 211.234KB
Recall Quarterly Report #1, 2019-4
RCLQRT-19V893-8349.PDF 211.137KB
Safety Bulletin
RCSB-19V893-3212.pdf 500.268KB
Defect Notice 573 Report
RCLRPT-19V893-5222.PDF 214.049KB
Recall Acknowledgement
Latest Recalls Documents
- 3 TYPES OF BRASS FITTINGS: This set includes DOT push-to-connect fittings, compression nylon tube fittings, and brass pipe fittings. It can be used for maintenance work in various scenarios, such as air brake systems and pipelines, to meet most of your needs
- 200PCS DOT FITTINGS SET: 30Pcs DOT push-to-connect fittings:7pcs straight male connector,7pcs 90°male elbow,6pcs union connector,4pcs union tee,4pcs 45°male elbow,2pcs schrader valve;123Pcs DOT compression nylon tube fittings:7pcs straight male connector,7pcs 90°male elbow,6pcs union connector,4pcs union tee,4pcs 45°male elbow,95pcs sleeve ferrules;45Pcs Brass pipe fittings:6pcs hex coupling,6pcs hex nipple,6pcs hex bushing,6pcs extension adapter,3pcs 90° street elbow,6pcs hex plug,12pcs socket plug;1pc 4m teflon tape;1pc tube cutter
- PREMIUM MATERIAL: These fittings are made of high-quality CA360 brass and meet D.O.T FMVSS 571.106, Air Brake system Requirements, with corrosion resistance, high-temperature flexibility, and low permeability
- PRESSURE RANGE: Airline fittings have pressure resistance, making them less likely to trip. Air brake fittings working pressure from vacuum max to 300 PSI. Temperature Range: -40° F to +250° F(Note: see tubing manufacturer’s recommendations for pressure and temperature limitations)
- EASY TO INSTALL: Our 200pcs fitting kit is easy to use in air systems and pipe connections. You need to use tools to fix loose parts to handle in tight places so that they will be firmer and not easily fall off. Some pieces that contain a threaded end already have sealant pre-applied, and we send Teflon tape as a gift to provide a secure connection
- 【Designed to withstand application extremes】The Dazakoot air line hose uniform dual-braided design consists of interwoven spirals providing greater flexibility and improved twist resistance compared to other spiral designs.
- 【Sprcifications】Meets or exceeds SAE J1402 - Type A - DOT FMVSS No. 106 - Air Brake Hoses, 49 CFR 571.106. 3/8" hose I.D - 1/2" end fittings. Designed for operating pressures up to 225 psi, Operating temperature of -40˚F to +200˚F (-40˚C to +93˚C) Replaces: Tectran 13S15401, Tremec Sloan 455180DSET, Philips 11-8115.
- 【Spring Joint】Air Brake Hose Assembly designed with large Red & Blue air line with a spring guard for easy coupling and uncoupling, these air lines save you time and effort. Plus, their durable construction and easy-to-install design provide peace of mind and reliable performance for years to come.
- 【360°Swivel End Fitting】 Swivel design featuring all brass construction, corrosion free 360°swivel fitting has long lifespan, with SAE standard 1/2 inch NPT port, threaded with seal glue to prevent leakage.
- 【All Parts in One】 Dazakoot has prepared a complete set of accessories for you, including: 1 pair of gladhand, 1 pair of extension grip, 2 rubber replacement seals. You don't have to visit multiple stores to equip yourself with these items. If you have any product issues, please contact Dazakoot customer service team, and they will provide you with assistance within 48 hours.
- 【FEATURES】Automatic Slack Adjuster Release Tool Wrench Set is designed to simplify installation and servicing of air brake systems in heavy-duty trucks, long-haul trucks, and trailers. This tool set makes brake service tasks easier and more efficient.
- 【Ease of Use】 The fork-end release tool securely fits under the brake system's pull pawl, allowing hands-free operation for servicing your truck. The tool is designed to release the tensioner button and safely adjust the brakes without prying or causing damage.
- 【Convenient for Any Mechanic Tool Set】The 5/16" double square ratcheting wrench with E-Z Grip handle adjusts the brake with ease. It features a side-mounted forward/reverse lever for simple operation.
- 【Time-Saving and Efficient】 The tools are made of durable carbon steel with oversized double injection handles that are comfortable to grip and use. Additionally, the double square offset reversible truck wrench provides reversible ratcheting action with an angled head for clearance.
- 【Quality Assurance】We are committed to providing high-quality products, and if you're not satisfied with our Automatic Slack Adjuster Release Tool Set, please feel free to contact us. We will do our best to address your concerns and solve any problems you may have.
- TYPE - Air Brake Chamber Type 3030 30/30 30 30
- REPLACEMENT - Bendix 165255 K049898 NT3030STD120 NT3030STD-120 802547 // Meritor 3030TN2-HNTRX-C // Dayton 3030C // Haldex GC3030 GC3030P40 // Freightliner 3030TS // Mack 19QE441RP1
- SPECS - Brake Chamber Type: 3030 // Stroke: Standard // Stroke Length: 2-1/2" // Port Thread: 2x3/8" NPT // Bolt Thread: 5/8"-11 UNC // Push Rod Length: 11-3/4" // Weight: 21lbs
- FEATURES -
- WARRANTY - 1-Year Unlimited Mile Warranty - includes assurances about the quality of the item, as well as a promise to provide replacement if something goes wrong within a set amount of time.
- 23 PCS PACKAGE: The 23 pcs DOT air brake fittings kit includes: 8 pcs 1/4 inch straight union DOT fittings, 8 pcs 3/8 inch straight union DOT fittings, 6 pcs 1/2 inch straight union DOT fittings, 1 pc tube cutter. DOT quick connect fitting assortment types: 1/4", 3/8", 1/2"
- PREMIUM QUALITY: The CheeMuii DOT air line quick connect fittings are made of high-quality CA360 brass, meet D.O.T. FMVSS 571.106 approved, SAE J1131 air brake system requirements, with corrosion resistance, high-temperature ductility, low permeability and long service life
- QUICK CONNECT FITTINGS: Our DOT push to connect fittings are extremely easy to install, can be sealed by pushing the tube firmly into the fitting and are also simple to remove from the tube
- MAX WORKING INTENSITY: The brass DOT air fittings can be operated in pressures from vacuum to 300 psi and in temperatures from -40°F to +200°F (-40°C to +93°C). Note: see the tubing manufacturer's recommendations for pressure and temperature mutations
- WIDE APPLICATION: The DOT air brake fittings can be used with air suspension systems, copper tubing in airline brake systems, perfect for truck /RV repair air line leak, also ideal for industrial workshops, daily garden or lawn mower repair, towing machine hose connection, etc
This product presentation was made with AAWP plugin.